background image

Network Camera User Manual 

92 

 

The  exported  certificate  should  be  saved  in  the  certificate  folder  of  your  client 

software before adding the device to your PC client. 

7.

 

Click the 

Save

 button to save the settings. 

 

Configuring QoS Settings 

Purpose: 

QoS (Quality of Service) can help solve the network delay and network congestion by 

configuring the priority of data sending. 

Steps: 

1.

 

Enter  the  QoS  Settings  interface: 

Configuration  >  Network  >  Advanced 

Settings > QoS 

 

 

 

QoS Settings 

2.

 

Configure  the  QoS  settings,  including  Video/Audio  DSCP,  Event/Alarm  DSCP 

and Management DSCP. 

The valid value range of the DSCP is 0 to 63. The bigger the DSCP value is, the 

higher the priority is. 

Note:

 DSCP refers to the Differentiated Service Code Point; and the DSCP value 

is used in the IP header to indicate the priority of the data. 

3.

 

Click 

Save

 to save the settings. 

Note

A reboot is required for the settings to take effect. 

 

Configuring 802.1X Settings 

Purpose: 

Содержание HiWatch HWI-B120H-U


































































































































































































Отзывы: