HIKVISION DS-K3B601-L Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 38

background image

Swing Barrier

·

Quick Start Guide

7

3.4

Terminal Description

Purpose:
The lane controller contains master lane controller and slave lane controller, which controls the IR
beams, motor, and other components work.

3.4.1

Master Control Board Terminal Description

Purpose:
The master lane control board contains lane communication interfaces, interconnecting interface,
motor encoder interface, remaining open and fire alarm interface, barrier opening directions
interface, people counting interface, remote control receiving antenna, motor drive interface,
brake interface, power interface, battery interface, DIP switch, and seven-segment display.

Note:

For detailed information about the DIP switch, see Appendix A DIP Switch Description.

The picture displayed below is the master control board diagram.

3.4.2

Slave Control Board Terminal Description

Purpose:
The  slave  lane  control  board  contains  lane  communication  interfaces,  interconnecting  interface,
motor  encoder  interface,  remaining  open  and  fire  alarm  interface,  barrier  opening  directions
interface,  people  counting  interface,  motor  drive  interface,  brake  interface,  power  interface,
battery interface, and seven-segment display.
The picture displayed below is the slave control board diagram.

«
...
13
14
15
16
17
...
»

Содержание DS-K3B601-L Series







































Отзывы:

Нет отзывов

Похожие инструкции для DS-K3B601-L Series

Бренд: iDTRONIC Страницы: 32

MHTM FlowMotion mTripod

Бренд: Magnetic Страницы: 84

Бренд: JKDC SECURITY Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды