background image

 

 

Swing Barrier

  

Quick Start Guide

 

ii 

 

Regulatory Information 
FCC Information 

Please take attention that changes or modification not expressly approved by the party responsible 

for compliance could void the user’s authority to operate the equipment. 

FCC compliance: This equipment has been tested and found to comply with the limits for a Class B 

digital  device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide 

reasonable  protection  against  harmful  interference  in  a  residential  installation.  This  equipment 

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance 

with the instructions, may cause harmful interference to radio communications. However, there is 

no  guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does 

cause  harmful  interference  to  radio  or television  reception,  which  can be  determined by turning 

the equipment off and on, the user is encouraged to try to correct the interference by one or more 

of the following measures: 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the  equipment  into an  outlet  on  a  circuit  different from that  to  which  the  receiver  is 

connected. 

Consult the dealer or an experienced radio/TV technician for help. 

This  equipment  should  be  installed  and  operated  with  a  minimum  distance  20cm  between  the 

radiator and your body. 

FCC Conditions 

This  device  complies  with  part  15  of  the  FCC  Rules.  Operation  is  subject  to  the  following  two 

conditions: 

1. This device may not cause harmful interference. 

2.  This  device  must  accept  any  interference  received,  including  interference  that  may  cause 

undesired operation. 

EU Conformity Statement 

This product and - if applicable - the supplied accessories too are marked with "CE" 
and  comply  therefore  with  the  applicable  harmonized  European  standards  listed 

under  the  RE  Directive  2014/53/EU,  the  EMC  Directive  2014/30/EU,  the  RoHS 

Directive 2011/65/EU.   

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed 

of as unsorted municipal waste in the European Union. For proper recycling, return 

this product to your local supplier upon the purchase of equivalent new equipment, 

or  dispose  of  it  at  designated  collection  points.  For  more  information  see: 

www.recyclethis.info 

 

Содержание DS-K3B601-L Series







































Отзывы:

Похожие инструкции для DS-K3B601-L Series