10
English
Riving knife function
a) Use the appropriate saw blade for the riving knife.
For the riving knife to function, the body of the blade
must be thinner than the riving knife and the cutting
width of the blade must be wider than the thickness of
the riving knife.
b) Adjust the riving knife as described in this
instruction manual.
Incorrect spacing, positioning and alignment can make
the riving knife ineffective in preventing kickback.
c) Always use the riving knife except when plunge
cutting.
The riving knife must be replaced after plunge cutting.
The riving knife causes interference during plunge
cutting and can create kickback.
d) For the riving knife to work, it must be engaged in
the workpiece.
The riving knife is ineffective in preventing kickback
during short cuts.
e) Do not operate the saw if the riving knife is bent.
Even a light interference can slow the closing rate of a
guard.
PRECAUTIONS ON USING CIRCULAR SAW
1. Use only blade diameter specified on the machine.
2. Do not use any abrasive wheel.
3. Do not use saw blades which are deformed or cracked.
4. Do not use saw blades made of high speed steel.
5. Do not use saw blades which do not comply with the
characteristics specified in these instructions.
6. Do not stop the saw blades by lateral pressure on the
disc.
7. Always keep the saw blades sharp.
8. Ensure that the lower guard smoothly and freely.
9. Never use the circular saw with its lower guard fixed in
the open position.
10. Ensure that the retraction mechanism of the guard
system operates correctly.
11. The saw blades body must be thinner than the riving
knife and the width of cut, or kerf (with teeth set) must
be greater than the thickness of the riving knife.
12. Never operate the circular saw with the saw blade
turned upward or to the side.
13. Ensure that the material is free of foreign matters such
as nails.
14. The riving knife should always be used except when
plunging in the middle of the workpiece.
15. For model C7UY, the saw blades range should be from
185 mm to 190 mm.
Body thickness: up to 1.5 mm, tip width: at least 1.9 mm
Riving knife thickness: 1.8 mm
16. Disconnect the plug from the receptacle before carrying
out any adjustment, servicing or
maintenance.
17. Check that there are no nicks or scratches in the cord.
18. Check the exterior and ensure that there is no damage.
19. Use a saw blade with a displayed rotational speed
equal to or higher than the rotational speed of the tool.
20. Use a saw blade that suits each different cutting
material.
21. Do not leave the saw placed on top of the guide rail.
22. Always hold handle of the tool firmly.
SPECIFICATIONS
Model
C7UY
Voltage (by areas)*
(110 V, 220 V, 230 V, 240 V)
Cutting Depth
90°
78 mm
45°
55 mm
Power Input*
1300 W
(110 V, 240 V: 1200 W)
No-load speed
5500 min
–1
Weight (without cord)**
4.5 kg
* Be sure to check the nameplate on product as it is subject
to change by areas.
** According to EPTA-Procedure 01/2014
STANDARD ACCESSORIES
(1) Saw Blade (mounted on tool)......................................1
(Dia. 190 mm ........... C7UY)
(2) Hex. bar wrench ...........................................................1
(3) Guide ............................................................................1
(4) Box wrench ...................................................................1
(5) Dust collector ...............................................................1
(6) M4 screw ......................................................................1
(7) Guide Rail Adapter .......................................................1
Standard accessories are subject to change without notice.
APPLICATION
Cutting various types of wood.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of sufficient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Prepare a wooden workbench (Fig. 1)
Since the saw blade will extend beyond the lower surface
of the lumber, place the lumber on a workbench when
cutting. If a square block is utilized as a workbench,
select level ground to ensure it is properly stabilized. An
unstable workbench will result in hazardous operation.
CAUTION
To avoid possible accident, always ensure that the
portion of lumber remaining after cutting is securely
anchored or held in position.
ADJUSTING THE SAW PRIOR TO USE
1. Adjusting the cutting depth
As shown in
Fig. 2
, hold the handle with one hand while
loosening the knob with the other.
The cutting depth can be adjusted by moving the base
to the desired position. In such manner adjust the
cutting depth and then securely retighten the knob.
2. Adjusting the riving knife
First tighten the knob and firmly secure the saw cover.
(
Fig. 2
)
0000Book_C7UY.indb 10
2019/01/30 9:40:55
Содержание C 7UY
