15
English
CAUTION
○
If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (o
ff
for
0.3 seconds). In such a case,
fi
rst let the battery cool,
then start charging.
○
When the charge indicator lamp
fl
ickers (at 0.2
-
second
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service Center.
○
Since the built
-
in micro computer takes about
3 seconds to con
fi
rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action
Figure
Page
Inclined cutting using the guide
(+45° direction) (sold separately)
9
3
Adjusting the base and saw blade to
maintain perpendicularity
10
3
Adjusting the cutting depth
11
3
Adjusting the angle of inclination
(0° – 45°)
12
-
a
3
Adjusting the angle of inclination
(45° – 55°)
12
-
b
3
Regulating the guide (sold separately)
13
3
Cutting line
14
4
Switch operation
15
4
About the mode select function (*1)
16
4
Remaining battery indicator
17
4
Using the LED light
18
4
Mounting the dust collector set
19
4
Removing and inserting the battery
20
5
Charging
21
5
Cutting (Do not use the tool with only
the blower function.)
22
5
Dismounting the saw blade
23
5
Mounting the Saw Blade
24
6
Charging a USB device from a
electrical outlet
25
-
a
7
Charging a USB device and battery
from a electrical outlet
25
-
b
7
How to recharge USB device
26
7
When charging of USB device is
completed
27
7
Selecting accessories
―
87
(*1) About the mode select function
Each time the mode selector switch is pushed, the
operation mode changes.
When Silent mode is selected, the Silent mode indicator
lamp lights up.
Silent mode reduces maximum motor RPM enabling
e
ffi
cient work with less noise.
If the load increases while the motor is operating in
Silent mode, it automatically changes to Power mode.
Additionally, if the load decreases again, it automatically
returns to Silent mode.
In Power mode, no change is made to Silent mode even
when the load decreases.
Mode
No
-
load speed
Power
4300 /min
Silent
2000 /min
NOTE
○
The mode will only change after a battery is installed and
the switch is pulled once.
○
The current mode will be maintained even if the switch is
on/o
ff
, or the battery is removed/reinserted.
LED LIGHT WARNING SIGNALS
(Fig. 28)
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered
during operation, the LED light will blink as described in
Table 3
. When any of the safeguard functions are triggered,
immediately remove your
fi
nger from the switch and follow
the instructions described under corrective action.
Fig. 28
Table 3
Safeguard Function
LED Light Display
Corrective Action
Overburden Protection
On 0.1 second/o
ff
0.1 second
If the operating with the shift knob set on
HIGH, adjust to LOW and continue operation.
Remove the cause of the overburdening.
Temperature Protection
On 0.5 second/o
ff
0.5 second
Allow the tool and battery to thoroughly cool.
00Book̲C3607DA̲Asia.indb 15
00Book̲C3607DA̲Asia.indb 15
2018/06/15 16:23:26
2018/06/15 16:23:26
