9
English
5) Battery tool use and care
a) Recharge only with the charger speci
fi
ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of
fi
re when used with another
battery pack.
b) Use power tools only with speci
fi
cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and
fi
re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a
fi
re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs,
fl
ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
e) Do not use a battery pack or tool that is damaged
or modi
fi
ed.
Damaged or modi
fi
ed batteries may exhibit
unpredictable behaviour resulting in
fi
re, explosion
or risk of injury.
f) Do not expose a battery pack or tool to
fi
re or
excessive temperature.
Exposure
to
fi
re or temperature above 130°C may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range speci
fi
ed in the instructions.
Charging improperly or at temperatures outside
the speci
fi
ed range may damage the battery and
increase the risk of
fi
re.
6) Service
a) Have your power tool serviced by a quali
fi
ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service providers.
PRECAUTION
Keep children and in
fi
rm persons away.
When not in use, tools should be stored out of reach of
children and in
fi
rm persons.
CORDLESS PLUNGE CUT SAW
SAFETY WARNINGS
Cutting procedures
a)
DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on auxiliary
handle, or motor housing.
If both hands are holding the saw, they cannot be cut by
the blade.
b) Do not reach underneath the workpiece.
The guard cannot protect you from the blade below the
workpiece.
c) Adjust the cutting depth to the thickness of the
workpiece.
Less than a full tooth of the blade teeth should be visible
below the workpiece.
d) Never hold the workpiece in your hands or across
your leg while cutting. Secure the workpiece to a
stable platform.
It is important to support the work properly to minimize
body exposure, blade binding, or loss of control.
e) Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
tool may contact hidden wiring.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and could give the operator
an electric shock.
f) When ripping, always use a rip fence or straight
edge guide.
This improves the accuracy of cut and reduces the
chance of blade binding.
g) Always use blades with correct size and shape
(diamond versus round) of arbour holes.
Blades that do not match the mounting hardware of the
saw will run o
ff
-centre, causing loss of control.
h) Never use damaged or incorrect blade washers or
bolt.
The blade washers and bolt were specially designed
for your saw, for optimum performance and safety of
operation.
Kickback causes and related warnings
-
kickback is a sudden reaction to a pinched, jammed or
misaligned saw blade, causing an uncontrolled saw to lift
up and out of the workpiece toward the operator;
-
when the blade is pinched or jammed tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator;
-
if the blade becomes twisted or misaligned in the cut, the
teeth at the back edge of the blade can dig into the top
surface of the wood causing the blade to climb out of the
kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a) Maintain a
fi
rm grip with both hands on the saw
and position your arms to resist kickback forces.
Position your body to either side of the blade, but
not in line with the blade.
Kickback could cause the saw to jump backwards, but
kickback forces can be controlled by the operator, if
proper precautions are taken.
b) When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to
a complete stop.
Never attempt to remove the saw from the work or
pull the saw backward while the blade is in motion
or kickback may occur.
Investigate and take corrective actions to eliminate the
cause of blade binding.
c) When restarting a saw in the workpiece, centre the
saw blade in the kerf so that the saw teeth are not
engaged into the material.
If a saw blade binds, it may walk up or kickback from the
workpiece as the saw is restarted.
d) Support large panels to minimise the risk of blade
pinching and kickback.
Large panels tend to sag under their own weight.
Supports must be placed under the panel on both sides,
near the line of cut and near the edge of the panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades produce narrow
kerf causing excessive friction, blade binding and
kickback.
0000Book̲C3606DPA.indb 9
0000Book̲C3606DPA.indb 9
2022/09/01 15:58:20
2022/09/01 15:58:20
Содержание C 3606DPA
Страница 2: ...2 1 0 45 0000Book C3606DPA indb 2 0000Book C3606DPA indb 2 2022 09 01 15 58 15 2022 09 01 15 58 15 ...
Страница 7: ...7 24 0000Book C3606DPA indb 7 0000Book C3606DPA indb 7 2022 09 01 15 58 19 2022 09 01 15 58 19 ...
Страница 318: ...318 0000Book C3606DPA indb 318 0000Book C3606DPA indb 318 2022 09 01 15 59 19 2022 09 01 15 59 19 ...
Страница 320: ...320 0000Book C3606DPA indb 320 0000Book C3606DPA indb 320 2022 09 01 15 59 19 2022 09 01 15 59 19 ...
