HID Corporation, 9292 Jeronimo Road, Irvine, CA 92618-1905, USA • Tel: (949) 598-1600, (800) 237-7769, Fax: (949) 598-1690
http://www.hidcorp.com
MaxiProx DFM Reader Installation Manual 5375-901 Rev D
Page
9 of 20
Table 8: Switch Description - SW5
Switch
Default
Description
1. Data Isolation 1
On
See 1 below
2. Data Isolation 0
On
See 1 below
3. RS422 Terminating Resistor
On
See 5 below
4. Serial Hardware line setting 1
O f f
See 6 below
5. Serial Hardware line setting 2
O f f
See 7 below
§
1. Open Collector Data Outputs SW5-1&2
when using Wiegand or Clock & Data Interface. The data outputs may be
configured so the MaxiProx is electrically isolated from the Host pull-up resistors. The default (standard) configuration is
non-isolated outputs, switches SW5-1 & 2 are
ON
.
Note
When the outputs are configured as isolated, separate power supplies should be used for the
MaxiProx and Host. These switches are unused when in RS232 or RS422 mode.
§
3. Beeper Control SW1-4:
The on-board beeper may be enabled or disabled. When enabled, the beeper tone is sounded
when the LED is green. SW1-4 in the
ON
position enables the beeper (the default).
§
2. LED Control SW1-5:
The LED flash after valid card read can be controlled by both the MaxiProx and Host, or Host
only. SW1-5 in the
OFF
position selects flash green after valid card read (the default).
§
4. LED Mode SW1-6:
Single/Dual Mode. With SW1-6
OFF
(default) it is in Single Mode. The LED is normally red, until
internal or host control turns it green (only a single control line is necessary). If
ON
, it is in Dual Mode, and the LED is
normally off (two control lines are necessary for host control of red and green).
§
5. SW5-3 Terminating Resistor:
Some RS422 connections require that the RX- line be terminated with a resistor to RX+.
If SW5-3 is in the
OFF
position, there is no terminating resistor on RX-. If SW5-3 is
ON
, then a 120-ohm resistor is
connected between RX+ and RX-.
§
6. SW5-4 Line Setting 1:
SW5-4 is used to configure the Reader's interface configuration. SW5-4 should be in the
OFF
position for RS232 or RS422 operation.
§
7. SW5-5 Line Setting 2:
SW5-5 is used to configure the Reader's interface configuration. SW5-5 should be in the
OFF
position for RS232 or RS422 operation.
2.9
2.9 Tamper Switch
Tamper Switch
Connect the tamper switch to the Host, if provided by the Host. When the cover is removed, the
tamper switch is released. The switch contacts available on TB1 Pins 4 and 5 and are either "normally
open" or "normally closed" dependent upon the position of the jumper on P1. Install the jumper to
connect pins 1 and 2 if you need the "normally open" contacts. Select the 2-3 position if you need the
"normally closed" contacts. "Normally closed" refers to the condition of the switch when the case is
open. The contacts are rated for 50 mA at 30 VDC.
2.10
2.10 Mounting
Mounting
Mount the base of the MaxiProx that holds the electronics to the surface using the holes located on
the base of the Reader. There are 12 recessed holes for mounting. The holes are not through holes and
require drilling before mounting. Chose the appropriate holes to be used and drill with a 5/32 (.156) inch
bit. Use #6 screws only. (See figure 2).
Проектирование
.
Монтаж
.
Продажа
. - http://vskd.ru
