HID ENTRYPROX Скачать руководство пользователя страница 30

Страница: 30 / 38

Page 30 of 38

September 2016

EntryProx User Manual, 4045-905, Rev. C.4

8.3

Resetting the Master Cod and System Defaults Only

Command 40 erases everything from the EntryProx memory except

the user list and transaction log

and restores the default settings. This is useful if the EntryProx unit has experienced programming

problems, or if you wish to delete earlier programming.
When you do this command the following rules apply:



If user #0 has not been programmed and user #1 is programmed then user #0 is erased and

user #1 is set to default (1234).



If user #0 has been programmed and user #1 has not been modified, user #0 and user #1 are

set to default data (1234).



If user #0 has been programmed and user #1 has been modified, user #0 is set to default

(1234) and user #1 is not changed.

Note:

You must change the master code after performing this command.

Place the EntryProx unit in program mode.
Press:

99 # Master Code *

Press:

40 # 00000 # 00000 # **

Press

to exit program mode

8.4

Erasing Entire Memory/Resetting System Defaults

Command 46 deletes everything from the EntryProx memory including the user list but not the

transaction log and restores the default settings. This is used as a last resort if you need to erase a

specific user and could not retrieve the Programmed User List. After performing this command the

master code must be reprogrammed.

Place the EntryProx unit in program mode.
Press:

99 # Master Code *

Press:

46 # 00000 # 00000 # **

Press

to exit program mode.

8.5

Turning KeyPress Audible Feedback On/Off

The Keypress Audible Feedback command enables the sounder to beep once for each key press.

This feature provides an audible acknowledgment that a particular key was pressed hard enough for

the unit to understand. The factory-shipped default setting is ON, but it can be toggled ON and

OFF as desired using command 30.

Place the EntryProx unit in program mode.
Press:

99 # Master Code *

To enable this feature
Press:

30 # 0 # 1 # **

To disable this feature
Press:

30 # 0 # 0 # **

Press

to exit program mode

Содержание ENTRYPROX







































Результаты поиска

Содержание ENTRYPROX

Отзывы:

Похожие инструкции для ENTRYPROX

Бренды по названию

Популярные бренды

HID ENTRYPROX, Руководство пользователя

Результаты поиска

Содержание ENTRYPROX

Отзывы:

Похожие инструкции для ENTRYPROX

Бренды по названию

Популярные бренды