HID ENTRYPROX Скачать руководство пользователя страница 2

Страница: 2 / 38

Page 2 of 38

September 2016

EntryProx User Manual, 4045-905, Rev. C.4

Copyright

form without the prior written permission of HID Global Corporation.

Trademarks

HID GLOBAL, HID, the HID logo, and EntryProx are the trademarks or registered trademarks of HID

Global Corporation, or its licensors, in the U.S. and other countries. All other trademarks, service

marks, and product or service names are trademarks or registered trademarks of their respective

owners.

Revision History

Date

Description

Version

September 2016

Removed references to PDAs and DCD/DTDs, which are no longer

supported.

C.4

March 2014

Added French translation of warning statement.

C.3

February 2007

Reformatted, added correct IP statement

C.2

August 2006

Error correction in EntryProx User Guide 4045-905 C.0 - page 33,

add ".com" to hidcorp URL

C.1

May 2006

Added PDA support for logging data.

C.0

Contacts

For additional offices around the world, see

www.hidglobal.com

corporate offices.

North America

Asia Pacific

611 Center Ridge Drive
Austin, TX 78753
USA
Phone: 866-607-7339
Fax: 949-732-2120

19/F 625 King’s Road
North Point, Island East
Hong Kong
Phone: 852 3160 9833
Fax: 852 3160 4809

Europe, Middle East and Africa

Brazil

Haverhill Business Park Phoenix Road
Haverhill, Suffolk CB9 7AE
England
Phone: 44 (0) 1440 711 822
Fax: 44 (0) 1440 714 840

Condomínio Business Center
Av. Ermano Marchetti, 1435
Galpão A2 CEP 05038-001
Lapa - São Paulo/SP
Brazil
Phone: 55 11 5514-7100

HID Global Customer Support:

www.hidglobal.com/support

Содержание ENTRYPROX







































Результаты поиска

Содержание ENTRYPROX

Отзывы:

Похожие инструкции для ENTRYPROX

Бренды по названию

Популярные бренды

HID ENTRYPROX, Руководство пользователя

Результаты поиска

Содержание ENTRYPROX

Отзывы:

Похожие инструкции для ENTRYPROX

Бренды по названию

Популярные бренды