HIAB 410K PRO Скачать руководство пользователя страница 8

Страница: 8 / 82

DANGER

• Carry out yourself only the service and

maintenance work you have the requisite
knowledge and experience of.

• All other maintenance work may only be

carried out by a Hiab authorised service
workshop.

• Make sure that every defect is rectified

immediately, according to the instructions.

• Follow the instructions exactly!
• All other work to rectify faults must be

performed by personnel in a Hiab
authorised service workshop!

WARNING

• Never clean the electronic system, plastic components, signs, or bearings with a

high-pressure jet cleaner. It could cause damage.

• Never expose the electronic system to high electrical voltages. This could

damage the control system.

• Never immerse the controller in water or other liquid. This will make the

controller unusable.

If your crane is equipped with add-on lifting equipment (hoist, rotator, etc.):

• The operation of the crane with add-on lifting equipment can differ from the

operation as described in this manual.

• You should therefore study the Operating Manual for the add-on equipment

carefully before you use the crane.

• Take particular note when placing the crane into or out of the transport position.

Introduction

HIAB 410K PRO

Содержание 410K PRO



















































































Результаты поиска

Содержание 410K PRO

Отзывы:

Бренды по названию

Популярные бренды

HIAB 410K PRO, Руководство оператора

Результаты поиска

Содержание 410K PRO

Отзывы:

Бренды по названию

Популярные бренды