HIAB 410K PRO Скачать руководство пользователя страница 76

Страница: 76 / 82

External Display [option]

Placing

The unit shall be placed under the plastic cover together
with the SPACE-box where it is protected from direct water
splash.

Start up

The External display automatically starts when the SPACE
system is started.

Operating modes

The display has three basic operating modes:

1. Use time mode (default)
2. Error display mode
3. Config mode

Use time mode (default)

By default the display shows how many hours the crane
has been used. (Levers not centred and oil not dumped).
Use time is shown on the display as:

• USE
• Number of thousands of hours
• Number of hours and a dot
• (Start over)

example use time=1526 hours

Error display mode

Press the button to switch to Error display mode. Display shows

a short time, and then start

showing errors as:

• The number of active errors and a dot.
• Each active error in turn (Blank display if no errors)
• (Start over)

Press the button again to return to Use time mode.

Example: 3 active errors, 003, 014 and 028

Clear errors

In Error display mode, errors can be cleared (as in SPACE terminal) by pressing the button for 2

seconds until the clear errors symbol

is shown in the display.

Maintenance and Service

HIAB 410K PRO

Содержание 410K PRO



















































































Результаты поиска

Содержание 410K PRO

Отзывы:

Бренды по названию

Популярные бренды

HIAB 410K PRO, Руководство оператора

Результаты поиска

Содержание 410K PRO

Отзывы:

Бренды по названию

Популярные бренды