Hi-Spec Xcel 1250 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 27

Hi-Spec Xcel 1250 Скачать руководство пользователя страница 17

Hi-Spec Xcel 1250

Operators Manual

Hi-Spec Engineering reserves the right to make changes or improvements at any time without incurring any obligation to

make such changes on products sold previously.

17

Recommended Maintenance

Every 25 operating hours

1.  Check and tighten all wheel nuts
2.  Check and tighten all nuts and bolts. Tighten if necessary. Use torques given.
3.  Check tire pressures.
4.  Check  all  hydraulic  hoses  and  hydraulic  cylinders  for  damage,  wear  and

leakage. Replace any damaged parts.

5. Grease all points.

Every 50 operating hours

1.  Check chain oiler reservoir. Top up with grade 10 hydraulic oil.
2.  Check all other gearbox oil levels.
3.  Check  wear  on  rear  spinners  and  on  the  chain  flails.  Turn  or  replace  if

necessary

Every 6 months

1. Check wheel bearings for any slackness. Adjust if required.
2. Remove hubcap and fill with grease.

Bolt tightening torques

Bolt tightening Torque (8.8 quality bolts)

Thread Dimension

Spanner Size (mm)

Tightening Moment (Nm)

M8

13

24

M10

17

48

M12

19

85

M14

22

135

M16

24

210

M18

27

290

M20

30

400

M22

34

550

M24

36

700

Tyre Details

The Xcel 1250 Spreader is fitted with Alliance 580/70 R38 (170A8/167B) tyre and
wheel assemblies. Hi-Spec Engineering recommends the use of these tyres only.

Recommended Pressures (Speed 25km/h)

Minimum

– 2.4 bar (35 psi)

Maximum

– 2.8 bar (41psi)

«
...
15
16
17
18
19
...
»

Содержание Xcel 1250




























Отзывы:

Нет отзывов