Herutu WCP-232-EXL Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 28

background image

WCP-232-EXL

12

5-4

．

Installation of WCP-EXL and WCP-232

The figure below shows the recommended mounting dimensions when connect WCP-EXL and WCP-232.

5-5

．

Connection to I / O terminal block

Follow the specifications below for the cable connected to the I / O terminal block.

・

Connection wire range 0.14mm2 to 1.5mm2 (common to single wire / stranded wire)

AWG26 to AWG16

・

Peeling wire length 6.0 mm (pre-soldering of the tip of the wire is not possible)

The tightening torque of the terminal block screw is 0.5Nm to 0.6Nm. Tighten with a flat-blade screwdriver.
When checking the continuity with the head of the terminal block screw, make sure that the screw is
tightened.

«
...
13
14
15
16
17
...
»

Содержание WCP-232-EXL





























Отзывы:

Нет отзывов

Похожие инструкции для WCP-232-EXL

Express5800/E120d-M

Бренд: NEC Страницы: 2

FrameSaver 9120

Бренд: Paradyne Страницы: 2

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: vPipes Страницы: 3

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

Бренд: Kanguru Страницы: 13

Бренд: ACTi Страницы: 12

Бренд: Comway Страницы: 20

Бренд: IBM Страницы: 72

Бренд: VIA Technologies Страницы: 2

PSJ-VZ58 gen3 OEM

Бренд: Grizzly Страницы: 12

Бренд: TERSUS Страницы: 7

Бренд: Arduino Страницы: 10

Бренд: National Instruments Страницы: 37

Бренд: Fujitsu Страницы: 7

Бренд: Fujitsu Страницы: 16

Бренд: Fujitsu Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды