HERKULES 23.424.04, Оригинальная инструкция по эксплуатации

Страница: 21 / 240

GB
- 21 -
6. Operation
6.1 ON/OFF switch (Fig. 1/7)
Switch position 0: O ff
Switch position I: Normal operation
Switch position AUTO: Automatic mode
6.2 Dry vacuuming
Use the pleated fi lter (24) for dry vacuuming (see
point 5.2). The dirt bag (27) can be fi tted in additi-
on when removing particularly stubborn dirt (see
point 5.3).
If you want to suction large amounts of fi ne dust,
you can use the coarse fi lter (16) (see section 5.2
Fitting the coarse fi lter).
Always ensure that the fi lters are perfectly secure.
6.3 Wet vacuuming
For wet-vacuuming, use the foam fi lter (25) (see
point 5.2).
For wet suctioning, fi t the sealing ring (37) (see
section 5.2 Fitting the sealing ring).
Check that the fi lter is securely fi tted at all times.
Water drain screw (Fig. 1/11)
To make the tank (10) easier to empty after wet
vacuuming, it is fi tted with a water drain screw
(11). Open the water drain screw (11) by turning it
anti-clockwise and drain the liquid.
To empty the container completely and easily, ap-
ply the castor brake (3) and tilt the container.
When wet vacuuming, the fl oating safety switch
(Fig. 2/21) closes when the maximum tank level
is reached. In doing so, the suction noise of the
equipment will change and become louder.
You must then switch o ff the equipment and em-
pty the tank.
Danger!
The wet and dry vacuum cleaner is not suitable
for the vacuuming of combustible liquids.
For wet vacuuming, use only the supplied foam
fi lter.
6.4 Automatic mode (Fig. 1)
Connect the power cable on your electric tool to
the automatic socket-outlet (4) and connect the
suction hose (9) to the extractor connector on
your electric tool. Check that the connections are
secure and air-tight.
You can use the supplied electric tool adaptor
(Fig. 3/22) to connect the suction hose (9) to the
electric tool. To do so, fi t it between the suction
hose and the extractor port on the electric tool.
Set the switch (7) on the wet and dry vacuum
cleaner to position AUTO, automatic mode. The
moment you switch on the electric tool, the wet
and dry vacuum cleaner switches on as well.
When you switch o ff the electric tool, the wet and
dry vacuum cleaner switches o ff as well after a
pre-set delay.
6.5 Blowing
Connect the suction hose (Fig. 1/9) to the blow
connector (Fig. 2/19) on the wet and dry vacuum
cleaner.
6.6 Filter cleaning system (Fig. 20a-20b)
The equipment has a fi lter cleaning system which
enables large amounts of fi ne dust to be suc-
tioned without fi tting the dirt collector bag.
Important! The fi lter cleaning system is only allo-
wed to be activated if the coarse fi lter is fi tted!
Important! The fi lter cleaning system can only be
activated if the equipment is in operation!
If there is a drop in suction performance, the fi lter
cleaning system can be activated at the touch of a
button in order to clean the dirty coarse fi lter and
increase the suction performance again.
Actuate the cleaning button (1) six times while
the equipment is in operation with the end of the
suction hose. Keep the button pressed down for
4 seconds each time you actuate it. Ensure that
the suction hose does not become kinked when
you do so.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
Anl_H_NT_50_Inox_SPK7.indb 21 Anl_H_NT_50_Inox_SPK7.indb 21 19.02.2018 15:41:59 19.02.2018 15:41:59