Henny Penny MVE-071 Скачать руководство пользователя страница 3

Страница: 3 / 56

These are the original version-controlled Henny Penny instructions for McDonald’s Electric Low Oil Volume (MVE) 1,

2, 3, and 4 vat, model 71, 72, 73 and 74 (MVE 71, 72, 73 and 74). This manual is available on the Henny

Penny Public website (www.hennypenny.com).

Read these instructions completely prior to installation and operation of this appliance to

ensure compliance to all required installation, operation and safety standards. Read and obey

all safety messages to avoid damage to the appliance and personal injury.

•

This fryer must be installed and used in a way that water does
not contact the oil which can cause splashing and boiling over
of oil and steam leading to personal injury; excludes normal
product moisture.

•

Burn risk! Do not move the fryer or filter drain pan while
containing hot oil. Personal injury or serious burns can result
from splashing hot oil.

This appliance is intended for commercial use in kitchens of restaurants, bakeries, hospitals, etc.

but not for the continuous mass production of food such as in a factory setting. During use the

units airborne A-weighted emission sound pressure is below 70 db(A). All repairs must be

performed by the manufacturer, its service agent or similarly qualified persons in order to avoid a

hazard.

Always use strain relief. Install the provided power cord with the ground wire dimensioned to fail

last. If the supplied power cord or an existing one becomes damaged, do not use it; rather, replace

it with a known good power cord. The power cord must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

Proper daily, weekly, monthly, quarterly and yearly maintenance must be performed on this

appliance to ensure safe and continuous operation. This appliance must never be cleaned with a

water jet or steam cleaning tool. Cleaning brushes are shipped with the appliance and proper

cleaning instructions are included in this manual.

Proper maintenance also increases the usable life of the appliance and oil, which reduces lifetime

operating costs. Additionally, old oil increases the possibility of surge boiling and fire due to the

reduced flash point of the oil. The oil temperature must never exceed 4

50⁰ F (230⁰ C).

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

This appliance is not intended to be operated by means of an external timer or a separate remote

control system.

Содержание MVE-071

























































Результаты поиска

Содержание MVE-071

Отзывы:

Henny Penny MVE-071, Руководство оператора, Страница: 3 / 56

Результаты поиска

Содержание MVE-071

Отзывы: