background image

Figure 13 - Demounting Lower Bead

15.

Turn the table top to rotate the wheel. The

demount head will guide the bead up and over the
edge of the wheel. Continue rotation until lower bead
is demounted.

Note:

With tube-type tires, demount the upper bead

and remove the tube before demounting the lower
bead.

Note:

Normal table top rotation for demounting is

clockwise.

At times during the mounting and
demounting procedure, the bead lifting tool
may encounter resistance or come under
load. Keep one hand firmly on the tool to
avoid possible tool disconnect. Turn the
table top counterclockwise to back out of
jam ups.

After successfully completing the demount

process, proceed to MOUNTING.

CAUTION

Important: Always read and follow the operating instructions.

• 5

Motorcycle

ATV

Operator Protective Equipment

Always wear durable work clothing during tire serv-

ice activity. Shop aprons or shop coats may also be
worn, however, loose fitting clothing should be
avoided. Tight fitting leather gloves are recom-
mended to protect the operator’s hands when han-
dling worn tires and wheels. Sturdy leather work
shoes with steel toes and oil resistant soles should
be used by tire service personnel to help prevent
injury in typical shop activities. Eye protection is
essential during tire service activity. Safety glasses
with side shields, goggles, or face shields are accept-
able. Back belts provide support during lifting activi-
ties and are also helpful in providing operator
protection.

Содержание Coats Rim Clamp RC-50M

















Отзывы:

Похожие инструкции для Coats Rim Clamp RC-50M