background image

Important: Always read and follow the operating instructions.

• iii

Operator Protective Equipment

Personal protective equipment helps make tire serv-

icing safer. However, equipment does not take the
place of safe operating practices. Always wear durable
work clothing during tire service activity. Loose fitting
clothing should be avoided. Tight fitting leather gloves
are recommended to protect operator’s hands when
handling worn tires and wheels. Sturdy leather work
shoes with steel toes and oil resistant soles should be
used by tire service personnel to help prevent injury in
typical shop activities. Eye protection is essential dur-
ing tire service activity. Safety glasses with side
shields, goggles, or face shields are acceptable. Back
belts provide support during lifting activities and are
also helpful in providing operator protection.
Consideration should also be given to the use of hear-
ing protection if tire service activity is performed in an
enclosed area, or if noise levels are high.

Definitions of Hazard Levels

Identify the hazard levels used in this manual with the

following definitions and signal words:

DANGER

Watch for this symbol:

It Means: Immediate hazards, which will result in

severe personal injury or death.

WARNING

Watch for this symbol:

It Means: Hazards or unsafe practices, which could

result in severe personal injury or death.

CAUTION

Watch for this symbol:

It Means: Hazards or unsafe practices, which may

result in minor personal injury or product or property
damage.

Watch for this symbol! It means BE ALERT! Your

safety, or the safety of others, is involved!

Safety Notices and Decals

Failure to follow danger, warning, and cau-
tion instructions may lead to serious per-
sonal injury or death to operator or
bystander or damage to property. Do not
operate this machine until you read and
understand all the dangers, warnings and
cautions in this manual. For additional
copies of either, or further information, con-
tact:

Hennessy Industries, Inc.

1601 J.P. Hennessy Drive

LaVergne, TN  37086-3565

(615) 641-7533 or (800) 688-6359

www.ammcoats.com

For additional information contact:

Rubber Manufacturers Association

1400 K Street N. W.

Washington, DC 20005

(202) 682-4800

Tire Guides, Inc.

The Tire Information Center

1101-6 South Rogers Circle

Boca Raton, FL 33487-2795

(561) 997-9229

www.tireguides.com

WARNING

CAUTION

WARNING

DANGER

Содержание Coats Rim Clamp RC-50M

















Отзывы:

Похожие инструкции для Coats Rim Clamp RC-50M