background image

11 

Helvar 478 8 Channel DALI Controller: Installation and User Guide

Use password

Note: The password is disabled by default.

You can use the factory-set password (58) for the module. Note that you must wait for 1 minute after choosing to use the 

password before the password lock functions.
If the password is enabled, you must enter the correct password. Otherwise you can only use the following functions/

menus:

• 

Change dimmer levels

• 

View technical information about the module

• 

 Recall a scene

• 

 Enter the password

If you chose to use the password, after 1 minute of inactivity, the LCD goes to standby and the ‘Enter password’ menu 

appears in ‘Main Menu’.

Use password

’ disables the functionality of the remaining menus. You can access the menus, but you cannot change any 

settings unless you enter the password (58).
A key (   ) is displayed in the bottom right of the screen when you enter the menu, to indicate that you cannot enter any 

settings.

Options:

Use password: (password is 58)
 

 (up button);

 

 x (down button)

 

(Default: x = no)

Press OK to confirm new selection, and a ‘

 

Done

’ message appears.

The password lock will be applied after a period of 60 seconds from this message appearing.

Enter password

If the password is enabled and you wish to use all of the functions of the module, you must enter the correct password.
The password is 58.

Status messages

Status messages are displayed on the bottom row of the LCD display.
The status LED will flash red to indicate the states listed below (except the ‘OK’ state).
The status LED lights red for a second when the 478 is powered on.

No DALI channel selected

If no DALI channel is selected, the messages ‘OK’ or ‘Fault’ are displayed.

Message

Reason

OK

The 478 unit and the DALI channels are working properly.

Fault

Fault with one or more DALI channels: see messages under ‘DALI channel 

selected’ on page 12.

No emergency ballast found

No emergency ballast could be detected on the selected channel.

D5

D1

Ch1

Ch5

Ch2

Ch6

Ch3

Ch7

Ch4

Ch8

D6

D2

D7

D3

D8

D4

D-

D-

D-

D-

D-

D-

D-

D-

DALI CHANNELS

DALI CHANNELS

OK

A

0V

SC

B

TERM

S-DIM

S-DIM

S-DIM

0V OVR

OVERRIDE

N

L

N

E

(85 to 264)VAC

DA+ DA-

OVERRIDE

DALI SYSTEM

478 DALI Controller

Содержание Digidim DALI 478
















Отзывы: