Helmer UltraCW II Скачать руководство пользователя страница 16

Страница: 16 / 22

Helmer Scientific Automatic Cell Washing System - UltraCW II

Operation Manual

360386/D

6 Product Specifications

6 .1

Operating Standards

These units are designed to operate under the following environmental conditions:

♦ Indoor use only.

♦ Altitude (maximum): 2000 m.

♦ Ambient temperature range: 5 °C to 40 °C.

♦ Relative humidity (maximum for ambient temperature): 80% for temperatures up to 31 °C, decreasing linearly to 50% at 40 °C.

♦ Transient over-voltages typically present on the MAINS supply.

♦ Do not exceed maximum loaded weight (including tubes and contents). Maximum weight is printed on rotor.

Table 3. Unit Specifications

UltraCW

Physical

Height

11” (280mm)

Width

13” (330mm)

Depth

18.9” (480mm)

Weight

53.8 lb (24.4 kg)

Rotor Radius

4.1” (105mm)

Maximum RPM / RCF

3500 RPM / 1438 RCF

Speed Tolerance

± 20 RPM

Kinetic Energy

250 Nm

Maximum Density

1.2 kg/dm

Noise Level

‹

49db

Electrical

Electrical Power (AC)

100V - 240V, 50/60 Hz

Electrical Power (DC)

6A @ 24 VDC

Fuses

10A / 250V

Maximum Current Consumption

2.2 A

Power Source

150W

Содержание UltraCW II






















Результаты поиска

Содержание UltraCW II

Отзывы:

Helmer UltraCW II, Руководство по эксплуатации, Страница: 16 / 22

Результаты поиска

Содержание UltraCW II

Отзывы: