Helm TMG-1200 Скачать руководство пользователя страница 12

The deviation displayed is calculated by the equation: 
 

       Deviation = Detected Value – Reference Value 

 
 

Ex)  Detected value: 1,823mm      Reference value: 1,798mm 

  

        1,823 – 1,798 = 0.025           Display value: 25 

 
 

The monitoring range depends on the set point.  When the set point is 100, the monitoring 

range is 

±

100 (m relative to the reference value.  Absolute value detection is characterized in that 

the value right after start is taken as reference for comparison with detected values, so slow 
changes such as overload by temperature can be detected.  To recommence sampling of 
reference data for absolute value detection during operation, push the sampling button.  Then 
sampling is recommended with the appearance of “Sampling” on the left side of the screen.  
Mean value detection is performed during sampling. 
 
 

 

Mean Value Detection 

 

When the machine is operated in the continuous mode, detection is dept turned off for a while 
during the initial 10 strokes (the initial number of bypasses the number of times that detection 
is turned off can be changed by system setting) and begins with the 11

th

 stroke.  Mean value 

detection is a detection mode which makes comparison with the mean value of 10 previous 
data (the number of averages taken can be changed by system setting) when the device gets 
into the detection condition after the end of the bypass state.  However, right after the start of 
detection, 10 previous data are not available.  Therefore, after the end of the bypass state, 
the 1

st

 data is compared with the last detected value at the end of bypass, the 2

nd

 data with 

the 1

st

 detected value, the 3

rd

 data with the mean value of the 1

st

 and 2

nd

 data, and the 4

th

 

data with the mean value of the 1

st

, 2

nd

 and 3

rd

 data.  Thus the data up to the 10

th

 are 

compared each with the mean value of previous data and the 11

th

 and subsequent data are 

compared each with the mean value of 10 previous data at all times. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Adaptive Mode 

(Stroke-to-Stroke "Rolling Average") 

Adaptive Mode 

(Stroke-to-Stroke "Rolling Average") 

Page 11 

TMG-1200 Instruction Manual 

Содержание TMG-1200























Отзывы: