background image

 

i

LIMITED WARRANTY 

 
 

Helm Instrument Co., Inc. (”HELM”) hereby warrants that the instruments and sensors 
(collectively the ”Product”) manufactured by it and sold to customer, are free from 
defects in material and/or workmanship under normal use subject to the following 
conditions. This warranty shall not apply to any Product which has been subjected to 
improper installation, misuse, negligence, accident, alteration, where service has been 
performed by other than an authorized Helm serviceman, or where the serial number 
has been defaced or altered. This warranty shall extend for the one (1) year period from 
date of shipment from our factory or authorized dealer, provided that the product is 
returned, freight prepaid, to Helm within the one (1) year warranty period within specific 
written authorization to perform repairs. Helm’s obligations and the exclusive remedy of 
customer under this warranty are limited to repairing or replacing any defective Product 
at no additional charge and returning Product to customer freight paid. Repair parts and 
replacement Products shall be furnished on an exchange basis and shall be either new 
or reconditioned. All replaced parts and Products shall become the property of Helm.  
 
EXCEPT AS SPECIFICALLY STATED HEREIN, HELM MAKES NO WARRANTIES 
EXPRESSED OF IMPLIED, OF THIS PRODUCT INCLUDING BUT NO LIMITED TO 
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 
PURPOSE, OR AS TO THE QUALITY, UTILITY OR PERFORMANCE, ALL QF WHICH 
ARE HEREBY EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE LIABILITY OF 
HELM EXCEED THE PURCHASE PRICE OF THIS PRODUCT. NOR SHALL HELM BE 
LIABLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO 
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL CHARGES, EXPENSE OR 
DAMAGES, ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT OR 
FOR ANY CLAIM BY ANY OTHER PARTY.  
 
Should you have any questions concerning this Warranty, you may contact Helm by 
writing or calling:  
 

HELM INSTRUMENT COMPANY, INC. 

CUSTOMER SERVICE 

361 WEST DUSSEL DRIVE 

MAUMEE, OHIO 43537 

(419) 893-4356

 

 
 

Содержание PTM-1100 Series















Отзывы: