Helion Invictus 10MT, Инструкция пользователя и развернутые схемы

Страница: 3 / 40

FEATURES OF THE INVICTUS 10MT
GETTING STARTED
CHARGING THE BATTERY
3
1/10th SCALE 4x4
BRUSHLESS POWERED
MONSTER TRUCK
1. Remove the body and battery from vehicle to prepare for charging.
a. Read charging instructions and understand all warnings and cautions before proceeding. This product is not a toy and
should not be charged, operated, or maintained without supervision of an adult.
b. Now is a good time to start charging so you can be up and running as soon as possible but remember to return to this guide
in the presence of the charging battery, remembering never to leave the battery unattended while charging .
2. Install the [4] AA type alkaline batteries into the transmitter.
3. Install the fully charged battery into the vehicle, be sure to straps around the battery and secure the hook and loop material to
keep the battery in place
4. Ensure the motor is plugged into the ESC.
5. Ensure the switch is in the OFF position and connect the battery to the ESC.
6. Read and understand transmitter cautions and setting instructions before use.
a. Confi rm settings for steering and throttle trim.
b. Confi rm ESC settings for the battery you will use (pre-programmed for included NiMH battery with reverse enabled)
7. Install body with 4 supplied clips; turn your equipment ON (radio fi rst!) and enjoy!
• Steel ring and pinion gear type four wheel drive drivetrain.
• Radient Reaktor brushless waterproof ESC and motor.
• Waterproof 6kg High Tourque servo.
• Water Resistant receiver box.
• HRS-3.1 2.4 GHz 3-Channel radio system.
• 1,800 mAh 9.6V 8-Cell NiMH rechargeable battery pack
with Tamiya-style plug.
• Four wheel independent suspension.
• Planetary metal gear differentials.
• Rubber sealed ball bearing supported drivetrain.
• Adjustable, oil fi lled, coil-over shock absorbers with blad-
ders.
• Adjustable suspension, camber, and front toe.
• Pivot ball style front suspension with upper arm.
• Stamped aluminum hinge pin braces.
• Dual bell crank steering with servo saver.
• Aluminum center drive shaft.
• Multi-purpose battery tray and straps, LiPo and NiMH
hump ready.
• Hex drive wheels
• Chevron style swamper tires and realistic wheels.
• Full size pickup body with fl ags.
• Adjustable body mounts.
• LiPo compatible and programmable ESC.
• Never leave the battery unattended while charging and never operate the charger without adult supervision.
• Never charge a warm battery, always allow the battery to cool to room temperature before charging.
• Never drop the charger or battery and do not attempt to charge a damaged battery.
• Inspect the battery and charger before use. Never use a battery or charger if the wire or connector has been damaged or if the
battery has experienced a short.
• Incorrect use of the battery, connections, or charging equipment can cause personal injury or property damage.
• Never allow batteries or charger to come in contact with moisture at any time.
• Stop charging immediately if the battery or charger becomes hot or changes form during use.
NOTE: Only use chargers designed for use with NiMH batteries for the RC industry, using the supplied connector. Use of
other (non-RC specifi c) chargers or connectors can permanently damage the battery and/or connected equipment. Genuine
NiMH replacement batteries and optoinal high current connectors are available at your local hobby dealer.
1. Plug the charger into a properly grounded standard AC wall plug.
2. Plug the battery into the charger and place the battery on/in a non-fl ammable surface/container away from fl ammable objects.
3. The LED on the charger should turn from RED to GREEN when charging.
4. A fully discharged battery should charge in approximately 4-5 hours.
a. Caution: Periodically monitor the temperature of the battery while charging, if the temperature exceeds 120°F
(49°C), disconnect the battery from the charger and allow it to cool before reconnecting.
5. Unplug the battery from the charger when the battery is slightly warm to the touch, and the LED has changed back to solid RED,
indicating the battery has been charged.
a. NOTE: Using a peak detection charger is recommended and will provide you with a faster and better charging experience.
We recommend the Origin NiMH or Primal Multi-Chemistry chargers by Radient RC.
b. Warning: Never charge the included battery at a charge current exceeding 2A.
6. Remove charger from wall plug.