
6 – 366
HEIDENHAIN Technical Manual TNC 426, TNC 430
To optimize the Z axis:
7
7
7
7
Select the range so that the vertical side is scanned.
Procedure for
optimizing the
machine
parameters
Procedure for optimizing the machine parameters:
7
7
7
7
Record ACTL. SPEED with the internal oscilloscope.
7
7
7
7
In the PROGRAM RUN, FULL SEQUENCE mode, select the OPTIDIGI
program and press the external START key. The machine runs and the
digitizing process begins.
7
7
7
7
Increase the feed rate with the override potentiometer until the nominal X
value has reached the maximum value and shows only minor voltage dips.
Make a note of the maximum feed rate that is possible in the worst axis.
(Axis should be just able to maintain a constant velocity.)
7
7
7
7
Are the oscillations in normal direction already perceptible, i.e. does the ball
tip lift off visibly from the workpiece surface?
• If not, then increase MP6230, e.g. by 10 mm/min. Return to the
PROGRAM RUN, FULL SEQUENCE mode, select the OPTIDIGI program
and press the machine START button...
• If so, then reduce MP6230 again, e.g. by 10 mm/min.
7
7
7
7
Repeat the optimization process for the Y axis. Also, switch the NC to the
scanning direction Y. The optimization process is oriented to the worst axis.
The feed rate must not be increased any further with either the override
potentiometer or the feed rate in normal direction (MP6230).
7
7
7
7
Repeat the optimization process for the Z axis. Change the scanning range
accordingly. The optimization process is oriented to the worst axis. The feed
rate must not be increased any further with either the override
potentiometer or the feed rate in normal direction (MP6230). Pay particular
attention to the vertical side.
Calculation of
possible
oscillations in
normal direction
7
7
7
7
Enter the calculated value in MP6210.
This standardizes the feed rate override potentiometer to the “attained feed
rate.”
MP6210 [1/s]
optimized F
scan
[mm/min]
PP.INT [mm]
60 [s/min]
⋅
--------------------------------------------------
=
Содержание TNC 426 CB
