HEIDENHAIN TNC 370 D Скачать руководство пользователя страница 71

Страница: 71 / 92

4–68

TNC 370 D

Machine Parameters

July 02

4.11 Tool Measurement with TT 130

Machine
parameter

Function and input

Change via

Reaction

MP6500

Tool measurement with TT 130
Input: %xxxx
Bit 0:
0 = Cycles for tool measurement disabled
1 = Cycles for tool measurement not

disabled

Bit 1:
0 = Tool radius measurement permitted;

tool length measurement with rotating
spindle

1 = Tool radius measurement and individual

tooth measurement disabled

Bit 2:
0 = Tool length measurement with

stationary spindle (bit 1 = 1)

1 = Tool length measurement with rotating

spindle. The tool length is then
calibrated with the spindle rotating only
if a tool radius offset (TT:R-OFFS) is
entered in the tool table.

Bit 3:
0 = Tool measurement with oriented

spindle stop

1 = Tool measurement without oriented

spindle stop. Individual-tooth measure-
ment is not possible. Tool radius
measurement might be incorrect.

PLC

MP6505

Probing direction for tool measurement
Input: 0 to 3
0 = Positive probing direction in the angle

reference axis (0° axis)

1 = Positive probing direction in the +90°-

axis

2 = Negative probing direction in the angle

reference axis (0° axis)

3 = Negative probing direction in the +90°-

axis

CN
PLC

MP6507

Calculation of the probing feed rate
Input: 0 to 3
0 = Calculation of the probing feed rate

with constant tolerance

1 = Calculation of the probing feed rate

with variable tolerance

2 = Constant probing feed rate

3 = Constant probing speed

CN
PLC

Содержание TNC 370 D





























































































Результаты поиска

Содержание TNC 370 D

Отзывы:

Похожие инструкции для TNC 370 D

Бренды по названию

Популярные бренды

HEIDENHAIN TNC 370 D, Техническая информация

Результаты поиска

Содержание TNC 370 D

Отзывы:

Похожие инструкции для TNC 370 D

Бренды по названию

Популярные бренды