background image

 

 

GENERAL USE – Remote Control

 

 
The top four rows of buttons are Hegel system remote control functions that can be used to control 
most Hegel amplifiers and CD-players. Functionality may differ from model to model. The bottom two 
rows are designated DAC and computer controls. 
 
Remote control buttons (starting top left) 

 

1. IN+ switches up to next input on your Hegel amplifier 

 

2. Mute for Hegel amplifiers  
3. VOL+ volume up for Hegel amplifiers  
4. IN- switches down to previous input on your Hegel amplifier  
5. ECO will put certain Hegel equipment in low power mode (sleep)  
6. VOL- volume down for Hegel amplifiers  
7. FILT filter selection button for HD12 and certain other Hegel products  
8. Stop/Eject for Hegel CD-players  
9. DISP display on/off for certain Hegel products  
10. Skip. to previous track on Hegel CD-players  
11. Play/Pause on Hegel CD-players  
12. Skip to next track on Hegel CD-players  
13. Skip to previous track on most computers/media players  
14. Play/Pause on most computers/media players  
15. Skip to next track on most computers/media players  
16. INPUT source selector button for Hegel DAC’s  
17. VOL- volume down for Hegel DAC’s  
18. VOL+ volume up for Hegel DAC’s 

 

 
 

Using the remote control to operate your HD12

 

The main buttons you will use to operate your HD12 are the buttons INPUT (16), VOL- (17) and 
VOL+ (18).  
 

Input: 

When you press the INPUT-button (16), or the  input selector button on the back of the right hand side, 
 the HD12 will switch to the next source input in the following sequence: COAX1 – OPTICAL1 – 
OPTICAL2 – USB – COAX1 and so on. On power up the HD12will remember the last used input. 

 
Volume control: 

The HD12 includes a built-in high quality digital volume control. This means that it can be used as a 
preamplifier and may be directly connected to a power amplifier. The volume can be increased or 
decreased by pressing and holding the VOL- (17) and VOL+ (18) buttons. The minimum output 
volume setting is 0 (mute) and the maximum is 100. 
When used together with a pre amplifier or integrated amplifier with its own volume control, the 
volume setting on the HD12 should be 100. This is also the default setting.  

REMEMBER: 

Factory volume setting is 100. However, if the volume setting is lower than 100 when 

power is turned off, the unit will start at a low-level default setting on the next power up. When you 
power up the unit the display will flash the volume setting for a few seconds. 
 

Содержание HD12









Отзывы: