Hedson IRT-UVA-1 PrepCure 4, Инструкция по эксплуатации

Страница: 5 / 12

714850 rev 1
5
protection facility for recycling.
The UV- radiation emission is: according to ANSI/IESNA
RP27.3-07 = Ris Group 3 (RG-3)
As appropriate measures; Always wear eye protection
during work in areas exposed to UV-radiation.
The lamp used in IRT UV-equipment have a spectrum that
start below 250nm but is of an ozone free type. To ensure
that the possible concentration of ozone is at a safe value
make sure to always work in a well-ventilated environment.
5. Markings
Markings on control unit:
714485 Warning! UV RADIATION CAN CAUSE INJURY AND
PROPERTY DAMAGE! Always wear eye protection, gloves and
protective clothing.
Machine sign
714526 WARNING UV emitted from this product. Avoid eye and skin
exposure to unshielded product.
Markings on cassette:
Do not use if protective glass is
broken or missing. This glass filters
the light from unwanted radiation.
Nicht verwenden, wenn die
Schutzglas beschädigt sind oder
fehlen. Dieses Glas filtert das Licht
von unerwuenschten Strahlung.
Ne pas utiliser si le verre protecteur
est cassé ou manquant. Ce verre
protecteur filtre la lumière en
bloquant le rayonnement non désiré.
Använd inte om skyddsglaset är
trasigt eller saknas. Skyddsglaset
filtrerar bort oönskad strålning.
Non utilizzare se il vetro di
protezione è rotto o mancante.
Questo vetro filtra la luce dalle
radiazioni indesiderate.
No lo utilice si el vidrio de
protección del cassette está roto o
le falta. Este vidrio filtra la luz de
la radición no deseada.
Må ikke brukes hvis
beskyttelsesglasset er ødelagt eller
fjernet. Beskyttelsesglasset filtrerer
bort uønsket stråling.
Niet gebruiken als beschermend
glas gebroken is of ontbreekt. Dit
glas filtert het licht van ongewenste
straling.
714490
714490 Do not use if protective glass is broken or missing. This glass
filters the light from unwanted radiation.
This document is the property of Hedson Technologies and may no
t be copied without our
written permission.The contents thereof must not be imparted to
a third party nor be used for
any unauthorized purpose. Contravention will be prosecuted.
Denna ritning är Hedson Technologies egendom. Den får icke vare
sig i ursprungligt eller
ändrat skick utan vårt medgivande kopieras eller mångfaldigas,f
örevisas för eller på annat
sätt delgivas eller utlämnas till tredje person. Överträdelse h
är av beivras med stöd av
gällande lag
Rev. Change description Appr. date Change no
1 FRISLÄPPNING 2016-12-16 7813
ISO 2768-m 2016-12-15
Certified by
Sheet
Rev
General Tolerance Scale
Description
Drawn by Approved by
1 (1)
Drawn date
AL 1:1
SKYLT VARNING LAMPBYTE (ETL)
LABEL WARNING LAMP REPLACEMENT (ETL)
714852 1
E
Article no
Material Surface finish Dimension Note
Designed by
AL
AL
Appr. by Rev. by
AL
Status
Approved
714852 WARNING Eye damage may result from directly viewing the
light produced by the lamp of this apparatus. For replacement of
lamp follow the instruction included in the UV-lamp replacement kit,
part number
714927.
410606 (Hot surface)
6. Operation
Turn the main switch on.
Set the timer to the recommended time by pressing
(+) or (-) buttons. To start the unit, press the Start/
Stop button. Also press Start/Stop button for an earlier
termination of the curing.
To see the remaining life time of the UV-lamps select
one of the lamps according to above and then press the
button with the percent sign (%).
NOTE : The restart of a hot lamp normally takes 4-6
minutes pending on the duration time in the recent
performed curing.
NOTE : When the curing process is terminated, do not
turn off the main switch before the cassette has, by the
fan, cooled down for about 5 minutes. Switching off the
dryer too early will shorten the lifetime of the UVA-lamps.
INDICATION DISPLAY OF
ACTIVE UV-LAMP AND
REMAINING UV LAMP TIME
SHOWN IN PERCENT
REMAINING UV-LAMP
TIME BUTTON
DISPLAY FOR UV-LAMP
SET/PRE-SET RUN TIME.
(DURING CURING:
REMANING RUN TIME)
UV-LAMP TIME SETTINGS
MAIN SWITCH
START/STOP BUTTON
ACTIVE UV-LAMP
SELECTION
(NOT APPLICABLE)
7. Maintenance
Before every usage,
check that:
— external cabling is not damaged
— protection glass in front of lamp is not cracked or
removed
— protection glass is clean and free from spray fog that
decreases the intensity