7. Program mode – General rules for navigation in the software
– The display shows software defined options in the bottom corner fields.
– To adjust the values use the arrow keys.
– To move to previous display without saving, press cancel.
7.1 Basic navigation
There are twelve predefined programs and three empty ones. All 15 programs have editable positions, names and drying
parameters.
Scroll up or down using the arrow keys, press select to run the program or view to edit.
7.2 Run
7.2.1 Distance check
The distance to the object within the circular
laser pattern is indicated on the display.
Adjust to the desired distance (60 cm is
default). If measuring fails ”Man´l dist”
appears (check distance manually).
Use the buttons on the keyboard to alter
between one or two active cassettes and to
turn on/off the temp. control. See chapter
8.1.
7.2.2 Start drying
Press start to begin the drying sequence.
The remaining time of the “flash off” will start
counting down. When the count down is
finished, the program automatically changes
to full bake mode.
7.2.3 Program graph
This graph is available when the temperature
control is active. The graph describes the
target, actual temperature, and remaining
time. See chapter 8.1.
7.2.4 Program values
This display shows the target and actual
temperatur of the drying object. It also shows
the used power capacity of the machine
and the actual energy usage of the drying
operation.
Note!
An inactive temperature control does
not show temperature values.
7.2.5 Energy usage
Shows the total energy usage per run for the
last 10 runs.
7.2.6 Drying complete
When flash off and full bake times have
expired the software returns to 7.1.
Note!
To extend the lifetime of the lamps,
the ventilators will continue to run for
cooling. After three minutes they turn off
automatically.
Note!
When the drying program is
completed the temperature control will
automatically reactivate.
7.3 Edit
7.3.1 Properties
The values of the chosen program will show
on the display.
By pressing the “Temperature control” button
the software switches between the properties
with and without the temperature control.
A change in either property is independent of
the other one. See chapter 8.1 for more info.
7.3.2 PIN Code
Use the arrow keys to set the correct digit.
Press enter to confirm and to edit the second,
third and fourth digit in the advanced PIN
code.
Note!
An entered PIN code is valid for all
entries until the main switch is turned off.
See chapter 9.2 for “advanced PIN code”.
7.3.3 Edit program parameters
When marked, change the value of the
parameters with the arrow keys. Press enter
to change the next value and so on. Pressing
enter for the last value directs the user to
editing of program position and name.
Press cancel to exit to 7.3.1 without saving any
parameters.
7.3.4 Edit prog. position/name
When marked, change the program number
with the arrow keys. Press enter to confirm
and to edit the next symbol.
7.3.5 Expansion of the program
steps
When the drying process requires more than
the two standard steps, you can expand the
number of steps in the drying cycle by linking
to the next program.
Start from point 7.3.4 and press Enter
repeatedly until the Link to next program
appears on the screen. Select with the arrow
keys Yes or No, and then press Save. The
link to the next program will remain until it
is deactivated (No). Use the program 13, 14
or 15 as these are free programs without any
default.
Note!
Changing the number will also change
the program position in the program list and
renumbering other programs.
Stop or cancel
returns to 7.1.
Stop or cancel
returns to 7.1.
Use
arrow keys
to set numbers.
The program
returns to 7.3.1.
The program
returns to 7.3.1.
1. Putty
2. Filler Bright
3. Filler Dark
4. Waterbase
5. Basecoat
6. Topcoat
7. Clearcoat
8. Plastic Filler
9. Plastic Topcoat
10. Plastic Clearcoat
11 Final boost
12. Soft cure
13. Free program 1
14. Free program 2
15. Free program 3
The program
returns to 7.3.1.
5
701012 rev 8
GB
