background image

12

9.0 SPARE PARTS

The following comprehensive list of spare parts is available for your Heatstore 

Ultima Profile Eco water heater. Please refer to the rating label on the right hand side 

of your heater before ordering to ensure the correct spare parts are obtained.

DO NOT REPLACE WITH PARTS NOT RECOMMENDED BY HEATSTORE 

- THIS WILL INVALIDATE YOUR GUARANTEE AND MAY RENDER THE 

INSTALLATION DANGEROUS.

1. 

Element assembly (incorporating start dry cutout) ...................... 95 607 952

2. 

Element assembly sealing gasket ............................................. 95 611 816

3. 

Primary cutout (vent pipe) ...................................................... 95 612 001

4. 

Solenoid valve assembly ........................................................ 95 605 877

5. 

Level sensor assembly (2.5ltr Model) ....................................... 95 606 971

 

Level sensor assembly (5.0/7.5ltr Model) ................................ 95 606 972

6. 

Circuit board (All Models) ...................................................... 95 615 076

7. 

Outlet tap headwork (inc. handle) ........................................... 95 605 099

8. 

Outlet tap stem ..................................................................... 95 605 832

9. 

Outlet tap cup seal ................................................................ 95 611 731

10. 

Bezel for tap & cover ............................................................ 95 605 072

11. 

Cover assy & screws (2.5ltr Model) ......................................... 95 614 131

 

Cover assy & screws (5.0ltr Model .......................................... 95 614 132

 

Cover assy & screws (7.5ltr Model) ......................................... 95 614 134

12. 

Steam condenser assy (2.5ltr Model) ....................................... 95 607 015

 

Steam condenser assy (5.0ltr Model) ....................................... 95 607 016

 

Steam condenser assy (7.5ltr Model) ....................................... 95 607 018

13. 

Condenser sealing gasket (2.5ltr Model) .................................. 95 611 817

 

Condenser sealing gasket (5.0ltr Model) .................................. 95 611 819

 

Condenser sealing gasket (7.5ltr Model) .................................. 95 611 820

14. 

‘O’ ring kit ........................................................................... 95 611 002

15. 

Manifold assy 2.5ltr .............................................................. 95 607 206

 

Manifold assy 5.0ltr .............................................................. 95 607 207

 

Manifold assy 7.5ltr .............................................................. 95 607 208

16. 

Outlet spout plastic - tank ....................................................... 95 604 668

17. 

Outlet spout - cover ............................................................... 95 604 001

18. 

Push fit connector 15x15 straight ............................................ 95 607 509

19. 

Push fit connector 15x15 elbow .............................................. 95 607 510

20. 

Tank (2.5ltr Model) ................................................................ 95 608 926

 

Tank (5.0ltr Model) ................................................................ 95 608 927

 

Tank (7.5ltr Model) ................................................................ 95 608 928

21. 

Tank drain & seal .................................................................. 95 608 929

22. 

Start dry cutout (element) ....................................................... 95 612 691

23. 

Solenoid valve coil ................................................................ 95 605 839

24. 

Fitting kit (2.5ltr Model) ......................................................... 95 607 024

25. 

Fitting kit (5.0/7.5ltr Model) .................................................. 95 607 025

26. 

Wiring harness LED ............................................................... 95 607 685

27. 

Wiring harness complete (2.5ltr Model) ................................... 95 607 686

 

Wiring harness complete (5.0/7.5ltr Model) ............................ 95 607 687

Содержание Ultima Profile Eco 2.5

















Отзывы: