background image

16

10.0 GUARANTEE

This product is guaranteed against faulty materials
and manufacture for a period of 10 years from date of
purchase 

(with the exception of the Expansion Vessel

which is guaranteed for a period of 5 years and valves,
fittings and electrical parts which are guaranteed
for a period of 2 years)

  provided that:

The unit has been installed in accordance with

the Installation and Service instructions and all rel-
evant Codes of Practice and Regulations in force at
the time of installation, and that all necessary inlet
controls and safety valves have been fitted correctly.

Any valves and controls are of the Heatstore rec-

ommended type and specification.

It has only been used for the storage of potable

water.

The unit has not been modified or tampered with

in any way, and has been regularly maintained as de-
tailed in the Installation and Service instructions.

The unit is not guaranteed against damage by frost,
and the inner container with integral immersion
heater(s) is not guaranteed against excessive scale
build-up.

Periodic loss of charge pressure from the Expansion
Vessel is normal (indicated by an intermittent discharge
of water  from the Expansion Valve)  and is not cov-
ered under the product guarantee. Refer to Section 7.5
for details on how to restore the Expansion Vessel
charge pressure.

This guarantee does not affect your statutory rights.

ENVIRONMENTAL INFORMATION

The Heatstore HSU products are manufactured from many
recyclable materials. At the end of their useful life they
should be disposed of at a Local Authority Recycling Cen-
tre in order to realise the full environmental benefits.

Insulation is by means of an approved CFC/HCFC free
polyurethane foam with an ozone depletion factor of zero.

The policy of Heatstore is one of continuous product development and, as such, we reserve the right to change
specifications without notice.

Island Park

Bristow Broadway

BRISTOL

BS11 9FB

Tel: 0117 923 5375

Fax: 0117 923 5374

Содержание HSUDC100

















Отзывы: