background image

     

            

  

 

 

 

Point of Use Water Heater 

Installation & Instruction Manual 

 

THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS  

(INCLUDING CHILDREN) WITH REDUCED PHYSICAL, SENSORY OR MENTAL 

CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY 

HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE 

 OF THE APPLIANCE BY A PERSON RESPONSIBLE FOR THEIR SAFETY. 

 

CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY 

 DO NOT PLAY WITH THE APPLIANCE. 

 

 

 

 

These instructions should be read in full before commencing the installation.                                                                                      
We recommend that the installation should only be carried out by a suitably qualified 

person. 

 

The 

Heatstore HS65VT-Eco

 heater is an open outlet, thermal storage water heater for 

use with Heatstore recommended fittings for one outlet only. 
It operates on the displacement principle i.e. when cold water is admitted into the 

bottom of the tank, hot water flows out through the outlet.  

 

Installation 

 

We recommend that this unit should be installed in the following order: 

 

1.

 

Fit wall bracket. 

 

2.

 

Fit mains electrical cable to the unit.  

 

3.

 

Fit heater to the wall. 

 

4.

 

Connect plumbing to the unit. 

 

5.

 

Replace the front cover. 

 

6.

 

Fill the unit with water and check for leaks. 

 

7.

 

Connect mains electrical cable to the fixed wiring. 

 

8.

 

Set the weekly mechanical timer. 

 

9.

 

Turn unit on and check operation. 

 

10.

 

Demonstrate operation to user. 

 

Please Note:- 
When removing the front cover, we recommend that you first remove the two top fixing 
screws, but only LOOSEN the two bottom screws. 

This will aid when replacing the front cover during installation. 

 

 

 
 
 
 
 

 

 
 

Содержание HS65VT-Eco









Отзывы: