background image

4

17789 Rev H

07/03

NA SERIES INSTALLATION INSTRUCTIONS

WARNING!

This fireplace and its components are designed to be installed and operated as a system. Any alteration to or

substitution for items in this system, unless allowed by these installation instructions, will void the Underwrit-

ers Laboratories listing and may void the product warranty. It may also create a hazardous installation. Read

through these instructions thoroughly before starting your installation and follow them carefully throughout

your project.

1. The Heatilator fireplace system consists of the following:

a.

Fireplace/Integral Grate

b.

Refractory

c.

Chimney Termination Cap

d.

Chimney System

e.

Hearth Extension

2. Optional Components Include:

a.

Glass Doors

b.

Chimney Air Kit

c.

Outside Combustion Air System

d.

Fan Kit

Note:

 

Illustrations  used  throughout  these  instructions

reflect “typical installations” and are for design purposes

only.   Actual  installation  may  vary  slightly  due  to  indi-

vidual design preferences. However, minimum and maxi-

mum clearances must be maintained at all times.
The  illustrations  and  diagrams  used  throughout  these

installation instructions are not drawn to scale.

Figure 1 - Typical Fireplace System

B. DESCRIPTION OF THE FIREPLACE SYSTEM

A.  LISTINGS AND CODE APPROVALS

This  fireplace  system  has  been  tested  and  listed  in

accordance with 

UL127

 and 

ULC-S610 

standards, and has

been listed by Underwriters Laboratories Inc. for installation

and operation in the United States and Canada as described

in this manual.
This fireplace has been tested and listed for use with the

optional  components  listed  on  page  5.  These  optional

components may be purchased separately and installed at

a later date. However, installation of an outside air kit will

require significant reconstruction, and should be installed

at the time of the initial fireplace installation.

Check with your local building code agency prior to installing

this  fireplace  to  ensure  compliance  with  local  codes,

including the need for permits and follow-up inspections. If

you need assistance during installation, please contact your

local  dealer  or  the  Heatilator  Technical  Services

Department,  Hearth  &  Home  Technologies,  1915  W.

Saunders St., Mt. Pleasant, Iowa 52641 (1-800-843-2848).

Heatilator® is a registered trademark of Hearth & Home

Technologies Inc., Division, HON INDUSTRIES.

Содержание NA36

































Отзывы: