Heatilator ICON100IH Скачать руководство пользователя

Страница: 1 / 68

Heatilator • ICON DV • 4042-300 Rev R • 06/07

Installation and service of this appliance should be performed

by qualified personnel. Hearth & Home Technologies

suggests NFI certi

ed or factory-trained professionals, or

technicians supervised by an NFI certi

ed professional.

Owner’s Manual

Installation and Operation

Models:
ICON60IT ICON100IT
ICON60ILT ICON100ILT
ICON60IH ICON100IH
ICON60ILH ICON100ILH
Direct Vent Gas Appliance

HOT! DO NOT TOUCH

SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.

WARNING

• Keep children away.
• CAREFULLY SUPERVISE children in same room as

appliance.

• Alert children and adults to hazards of high

temperatures.

• Do NOT operate with protective barriers removed or

door open.

• Keep clothing, furniture, draperies and other

combustibles away.

Glass and other surfaces are hot during
operation and cool down.

This appliance has been supplied with an integral barrier to
prevent direct contact with the

xed glass panel. Do NOT

operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the bar-
rier is not present or help is needed to properly install one.

This appliance may be installed as an OEM installation

in manufactured home (USA only) or mobile home and

must be installed in accordance with the manufacturer’s

instructions and the manufactured home construction and

safety standard,

Title 24 CFR, Part 3280

Standard for

Installation in Mobile Homes, CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas

indicated on the rating plate.

DO NOT DISCARD THIS MANUAL

CAUTION

• Important operating and

maintenance instructions
included.

•

Leave this manual with
party responsible for
use and operation.

•

Read, understand and follow
these instructions for safe
installation and operation.

NOT

DISCARD

In the Commonwealth of Massachusetts:

• installation must be performed by a licensed plumber

or gas fitter;

See Table of Contents for location of additional Common-
wealth of Massachusetts requirements.

If the information in these instruc-
tions is not followed exactly, a

re may result causing property

damage, personal injury, or death.

• Do not store or use gasoline or other

am-

mable vapors and liquids in the vicinity of

this or any other appliance.

• What to do if you smell gas:

- Do not try to light any appliance.

- Do not touch any electrical switch. Do not

use any phone in your building.

- Immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions.

- If you cannot reach your gas supplier, call

the

re department.

• Installation and service must be performed

by a quali

ed installer, service agency, or

the gas supplier.

WARNING

Содержание ICON100IH





































































Результаты поиска

Содержание ICON100IH

Отзывы:

Похожие инструкции для ICON100IH

Бренды по названию

Популярные бренды

Heatilator ICON100IH, Руководство пользователя

Результаты поиска

Содержание ICON100IH

Отзывы:

Похожие инструкции для ICON100IH

Бренды по названию

Популярные бренды