Heatilator HEIR36H-IFT Скачать руководство пользователя

Страница: 44 / 66

Heatilator • HEIR36-IFT, HEIR42-IFT, HEIR50-IFT Installation Manual • 2458-980 Rev. B • 8/17

E. Air Shutter Setting

Natural Gas (NG) installations

As a general rule, it is acceptable to reduce the shutter

opening to adjust for vertical vent pipe sections prior to

the initial fire up.

• Vertical Termination: May reduce shutter setting by 1/8 in.
• Horizontal Termination (more than 4 ft. vertical in vent

configuration): May reduce shutter setting by 1/8 in.

• Horizontal Termination (less than 4 ft vertical in vent

configuration): May reduce shutter setting by 1/16 in.

Propane (LP) installations

• It is recommended that the air shutter on propane

appliances remain at full open position.

Air Shutter Adjustment

Adjustment can be made to the air shutter with or without

the logs installed with a ¼ in. nut driver. See Figure 1.

Air Shutter Setting

Air shutter settings should be adjusted by a qualified ser-

vice technician at the time of installation. The air shutter

is pre-set at the factory for minimum vertical, maximum

horizontal vent run for this appliance: 2 ft. vertical and 7

in. horizontal).

Factory Pre-Set Air Shutter Settings

To adjust air shutter:
•   Loosen the screw on the burner assembly.
•   To close the air shutter, turn shutter clockwise.
•   To open air shutter, turn shutter counterclockwise.
•   Tighten the screw.

NOTICE:

Flames should not appear orange or stretch to

the top refractory. If sooting occurs, provide more air by

opening the air shutter.

Shutter Setting Verification / Flame Appearance

• After

15 minutes, the flames will be a yellow/blue mix.

The front flames may be blue at this time.

• After 30 minutes, the flames should be yellow with

some blue flames near the burner ports.

• After 1 hour, the flame will be at its maximum maturity.

Note:

Visually, a propane flame may differ from a

natural gas flame. This is due to the different chemical

compositions that make up both fuel types. In general, the

LP flames may be a little shorter and much brighter than

a natural gas flame.

Figure 1. Air Shutter Location

MODEL

HEIR36H-IFT

HEIR36T-IFT

5/8 in.

Full Open

HEIR42H-IFT

HEIR42T-IFT

5/8 in.

Full Open

HEIR50H-IFT

HEIR50T-IFT

5/8 in.

Full Open

Содержание HEIR36H-IFT



































































Результаты поиска

Содержание HEIR36H-IFT

Отзывы:

Похожие инструкции для HEIR36H-IFT

Бренды по названию

Популярные бренды

Heatilator HEIR36H-IFT, Руководство по установке

Результаты поиска

Содержание HEIR36H-IFT

Отзывы:

Похожие инструкции для HEIR36H-IFT

Бренды по названию

Популярные бренды