manualshive.com logo in svg

Heatilator GBCL36 Series, Руководство пользователя, Страница: 27 / 60

Поделиться
Скачать
Heatilator GBCL36 Series Скачать руководство пользователя страница 27

 

Heatilator • Caliber Multi-Sided B-Vent • 4002-094 Rev H • 11/07 

27

A. Before Lighting Appliance

Before lighting this appliance, determine if it has a stand-
ing pilot or Intelli

fi

 re ignition system by opening the control 

access panel to view wiring system and gas valve. If this 
appliance has a red or black ignitor button (See Figure 10.1) 
this appliance has a standing pilot ignition system. If there is 
no red or black ignitor button, this appliance has an Intelli

fi

 re 

ignition system.

If installing Intelli

fi

 re Ignition battery backup:

•  Do not install batteries if the backup mode may 

not be used for extended time.

•  Batteries may leak.
•  Install batteries only when needed for power 

outage.

CAUTION

Fire Risk
Combustion Fumes Risk

Glass door 

MUST

 be in place when appliance 

is operating. 
Do NOT operate appliance with glass door 
removed.
•  Open viewing glass for servicing only.
•  Glass door MUST be in place and sealed 

before operating appliance.

•  Only use glass doors certi

fi

 ed for use with 

the appliance.

•  Glass replacement should be done by 

quali

fi

 ed technician.

WARNING

Before operating this appliance, have a quali

fi

 ed 

technician:

•  Remove all shipping materials from inside and/or 

underneath the 

fi

 rebox.

•  Review proper placement of logs, rockwool, lava rock and 

vermiculite.

•  Check the wiring.
•  Check the air shutter adjustment.
•  Ensure that there are no gas leaks.
•  Ensure that the glass is sealed and in the proper 

position.

•  Ensure that the 

fl

 ow of combustion and ventilation air is 

not obstructed (front grilles and vent caps).

13 

13 

Operating Instructions 

HOT SURFACES!

Glass and other surfaces are hot during 
operation and cool down.

WARNING

•  CAREFULLY SUPERVISE children in same room as 

appliance.

•  Alert children and adults to hazards of high 

temperatures.

High temperatures may ignite clothing or other 

fl

 ammable materials.

•  Keep clothing, furniture, draperies and other combustibles 

away. 

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
•  Keep children away 

This  appliance  has  been  supplied  with  an  integral 
barrier to prevent direct contact with the 

fi

 xed glass 

panel. Do NOT operate the appliance with the barrier 
removed.

Contact your dealer or Hearth & Home Technologies if the 
barrier is not present or help is needed to properly install one.

Improper installation, adjustment, alteration, service or 
maintenance can cause injury or property damage. Refer 
to the owner’s information manual provided with this 
appliance. For assistance or additional information consult 
a quali

fi

 ed installer, service agency or the gas supplier.

WARNING

Do NOT use this appliance if any part has been under 
water. Immediately call a quali

fi

 ed service technician 

to inspect the appliance and to replace any part of the 
control system and any gas control which has been under 
water.

WARNING

¨

Содержание GBCL36 Series





























































Отзывы:

Нет отзывов