manualshive.com logo in svg

Heatilator GBCL36 Series, Руководство пользователя, Страница: 23 / 60

Поделиться
Скачать
Heatilator GBCL36 Series Скачать руководство пользователя страница 23

 

Heatilator • Caliber Multi-Sided B-Vent • 4002-094 Rev H • 11/07 

23

E. Install the Junction Box

•  Remove the junction box assembly from the valve 

compartment.

•  If the box is being wired from the OUTSIDE of the 

appliance:
-  Loosen two screws on the Romex connector, feed the 

necessary length of wire through the connector and 
tighten the screws.

-  Make all necessary wire connections to the receptacle,  

assemble the receptacle and cover to the junction 
box.

-  Attach the junction box assembly to the outside of the 

appliance with the two screws provided.

•  If the box is being wired from the INSIDE of the 

appliance:
-  Pull the electrical wires from outside the appliance 

through this opening into the valve compartment.

-  Loosen the two screws on the Romex connector, feed 

the necessary length of wire through the connector and 
tighten the screws.

-  Make all necessary wire connections to the receptacle, 

assemble the receptacle and cover to the junction 
box.

-  Attach the junction box assembly to the inside of the 

appliance with the two screws provided.

•  If the box is not to be wired at the time of appliance 

installation, assemble the receptacle and cover to the box 
and install on the inside of the appliance.

Shock Risk
Explosion Risk

Do NOT wire 110V to valve.
Do NOT wire 110V to wall switch
•  Incorrect wiring will damage millivolt 

values.

•  Incorrect wiring will override IPI safety 

lockout and may cause explosion.

WARNING

BLACK

WHITE

GROUND

14-2 with

Ground Romex

Figure 10.4  Junction Box Detail

14-2

 

with ground Romex is the recommended 

wiring to the appliance junction box.

¨

Содержание GBCL36 Series





























































Отзывы:

Нет отзывов