Heatilator ECO-ADV-PS35 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 28

Heatilator ECO-ADV-PS35 Скачать руководство пользователя страница 3

6/16//2014

7058-205A

3

HEATILATOR ECO-CHOICE

Model

ECO-ADV-PS35, ECO-ADV-PS50
and ECO-CAB50

Laboratory

Intertek

Report No.

3198406

Type

Solid Fuel Room Heater/Pellet Fuel Burn-

ingType

Standard

ASTM E1509-04 and ULC S627-00, ULC/
ORD-C1482-M1990 Room Heater Pellet
Fuel Burning type and (UM) 84-HUD, Mo-
bile Home Approved.

FCC

Complies with Part 15 of FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.

These heaters meet the US Environmental Protection
Agency’s Emission limits for pellet heaters. Under specifi c
conditions the Eco-Choice PS35, PS50 & CAB50 stove
has shown to deliver heat at rates ranging from 9,200 to
31,400 BTU/hr.

1

Important Safety Information

Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualifi ed
installer, service agency or your dealer.

• Installation and use of any damaged appliance.

• Modifi cation of the appliance.

• Installation other than as instructed by Hearth & Home

Technologies.

• Installation and/or use of any component part not approved by

Hearth & Home Technologies.

• Operating appliance without fully assembling all components.

• Operating appliance without legs attached (if supplied with unit).

• Do NOT Overfi re - If appliance or chimney connector glows,

you are overfi ring.

Any such action that may cause a fi re hazard.

WARNING

Fire Risk

Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided by,
the following actions:

C. Glass Specifi cations

This stove is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.

D. Electrical Rating (on high)

Model PS35

:

115 VAC, 60 Hz, Start 3.8 Amps, Run 1.3 Amps

Model PS50

:

115 VAC, 60 Hz, Start 5.1 Amps, Run 3.0 Amps

Model CAB50

:

115 VAC, 60 Hz, Start 5.1 Amps, Run 3.0 Amps

E. Mobile Home Approved

•

This appliance is approved for mobile home installa-
tions when not installed in a sleeping room and when
an outside combustion air inlet is provided.

•

The structural integrity of the mobile home fl oor, ceil-
ing, and walls must be maintained.

•

The appliance must be properly grounded to the frame
of the mobile home with #8 copper ground wire, and
use only listed double-wall connector pipe.

•

Outside Air Kit, part 811-0872 or OAK-3 must be in-
stalled in a mobile home installation.

•

Unit must be secured to mobile home structure.

Note: The appliance is also approved for installation
into a shop

A. Appliance Certifi cation

MODEL: PS35

EPA Certifi ed:

2.1 grams per hour

Effi ciency:

78%

EPA BTU Output:

9,200 - 24,400 / hr

Heating Capacity:

750 - 1,450 square feet
depending on climate zone

Vent Size:

3” or 4” L or PL

Hopper Capacity:

45 lbs

Fuels:

Wood pellets

Shipping Weight:

210 lbs

MODEL: PS50 / CAB50

EPA Certifi ed:

1.7 grams per hour

Effi ciency:

78%

EPA BTU Output:

11,900 - 31,400 / hr

Heating Capacity:

1,225 - 2,200 square feet
depending on climate zone

Vent Size:

3” or 4” L or PL

Hopper Capacity:

83 lbs / 120 lbs

Fuels:

Wood pellets

Shipping Weight:

240 lbs / 266 lbs

*BTU will vary, depending on the type of fuel you use in your
appliance. Consult your Heatilator dealer for best results.

B. BTU & Effi ciency Specifi cations

NOTICE:

This installation must conform with local codes. In

the absence of local codes you must comply with the

ASTM

E1509-04, ULC S627-00, (UM) 84-HUD and ULC/ORD-
C-1482.

«
1
2
3
4
5
...
»

Содержание ECO-ADV-PS35





























Отзывы:

Нет отзывов