Heatilator ECO-ADV-PS35 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 28

Heatilator ECO-ADV-PS35 Скачать руководство пользователя страница 22

22

7058-205A

6/16/2014

HEATILATOR ECO-CHOICE

B.

Top Vent Adapter Installation

3 to 3 inch Top Vent Adapter
3 to 6 inch Top Vent Offset Adapter

Installing the Top Vent Adapter

1.

Put a layer of high temperature silicone on the 3 inch
(76mm) exhaust outlet.

Do not put silicone inside of

pipe. Figure 22.1

2.

Slide the top vent adapter onto the rear exhaust outlet
and adjust the assembly to a vertical position.

Figure

22.1.

3.

Drill 4 holes with #26 drill bit (provided) into the back of
the appliance using the outer shield as a pattern (make
sure the assembly is vertical).

Figure 22.1.

4.

Install the 4 mounting screws.

5. Drill 2 holes with #26 drill bit through the rear exhaust

outlet using the 2 holes already in the short horizontal
pipe in the top vent adapter as a guide. Install the 2
screws.

Figure 22.1.

6.

Install the vent pipe into the top vent adapter (be sure to
silicone all joints).

7.

To clean the top vent adapter open the clean-out cover.

Figure 22.1.

Silicone Rear Exhaust Outlet

3 to 6 inch
Offset Adapter

3 to 3 inch
Offset Adapter

Use Hole on Each
Side as Drilling Guide

Figure 22.1

C. Rear Vent & Rear Vent to Top Vent Adapter
Installation

1.

Put a layer of high temperature silicone on the 3 inch
(76mm) exhaust outlet.

Do not put silicone inside of

pipe. Figure 22.1.

2.

Slide the adapter onto the rear exhaust outlet and adjust
the assembly to the appropriate position.

3.

Install the vent pipe into the adapter (be sure to silicone
all joints)

Clean-Out Cover

Clean-Out Cover

Figure 22.2 - Rear Vent Adapter

Figure 22.3 - Rear to Top Vent Adapter - 90

o

«
...
20
21
22
23
24
...
»

Содержание ECO-ADV-PS35





























Отзывы:

Нет отзывов