Heat&Glo 6000C-IPI Скачать руководство пользователя страница 64

Страница: 64 / 85

Heat & Glo • 6000C-IPI, 8000C-IPI • 2164-900 Rev. W • 8/14

Figure 7

Figure 8

Figure 9

Figure 10

Log #3 (SRV2168-703)

: Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1.

After slot and tab have been

tted together, mate the groove located on the bottom of Log #3 with the horizontal grate bar

and far right grate tine. Log # 3 will sit down on top of both the grate tine and the horizontal grate bar (see Figure 7).

Log #4 (SRV2168-704)

: Place Log #4 in the left log indentation on the burner top (see Figure 2). Slide Log # 4 from right to

left under Log #2 to

t completely and securely into the indentation (see Figure 8). The back or Log # 4 should rest against

the far left grate tine as well as contact Log # 2.

Log #5 (SRV2168-705)

: Place Log #5 in the right log indentation on the burner top (see Figure 2). Ensure the log

completely and securely in the indentation (see Figure 9). Log #5 should be pulled to the left hand side of log indentation.

Log #6 (SRV2168-706)

: Mate the groove located on the lower end of Log #6 with the fourth tine (from left to right) as

shown in Figure 10. Set the other end of Log #6 on the

at area located on top of Log #4 (see Figure 9). Log #6 will

also rest against center grate tine. When properly installed, Log #6 will rest securely on all 3 contact points, not allowing
movement or shifting.

FLAT AREA

LOG CONTACTS GRATE TINES

LOG #6 CONTACTS TOP OF LOG #4

RIGHT GRATE TINE

LOG #4 CONTACTS LOG #2

HORIZONTAL GRATE BAR

2168-935C

Содержание 6000C-IPI






















































































Результаты поиска

Содержание 6000C-IPI

Отзывы:

Heat&Glo 6000C-IPI, Руководство пользователя, Страница: 64 / 85

Результаты поиска

Содержание 6000C-IPI

Отзывы: