background image

MODBUS Installation and Operation Manual

 

 

3

HT# 059266-00A

MODBUS TyPe

•   Heat-Timer Platinum controls can be ordered with or upgraded to MODBUS communication.

•   The Platinum MODBUS communication uses RTU protocol and RS485 wiring.

•   When upgrading a standard Platinum control to MODBUS communication, the CPU 

Board on the back of the Platinum control must be replaced.  In addition, the MODBUS 

Communication Board must be installed.  See "Platinum Control Rear View" on page 1.

Motherboard

CPU Board

A(+)

G

B(-)

PlaTInUM Panel COnneCTeD 

TO MODBUS neTWOrK

Connect to MODBUS

RS485 Network

MODBUS

Communication

Board

MODBUS rS485 WIrIng

•   Heat-Timer Platinum control MODBUS communication uses a RS485 connection.

•   Connect the RS485 to the back of the Platinum control's MODBUS Communication Board.

•   Use 18 AWG Twisted-Pair cable.  The cable length must not exceed 3500 feet.

•   The Ground RS485 terminal (G) MUST be connected to the BMS RS485 Ground.

 alerT

DO NOT USE the RS485 Connector on the Motherboard for MODBUS communication .

Use the RS485 Connector on the MODBUS Communication Board instead .

MODBUS rTU COMMUnICaTIOn COnfIgUraTIOn

•   If the Platinum control was purchased with or upgraded to a MODBUS communication, some 

of the following settings must be configured to guarantee proper communication.

--NETWORK SETTINGS--

 MAC Address 

1

 Baud 

9600

MODBUS COMMUnICaTIOn OPTIOnS

SELECT: 

MENU/<Maintenance>/Network Settings

 

Multi-MOD Platinum

SELECT: 

MENU/<Settings>/<More Settings>/<Remote Interface>/Network Settings

 

All Other Platinum Controls

•   Before connecting the Platinum control to the MODBUS network, the user must set the following parameters according to the 

MODBUS Network Administrator's instructions.

MaC aDDreSS

Options: 

From 1 to 247

 

Default: 1

•   This is a unique ID within the MODBUS network.  It must be provided by the MODBUS 

Network Administrator.

---- MAC ADDRESS ---

      1

[            ]

BaUD

Options: 

9600, 19200, 38400

 

Default: 9600

•   The Baud determines the speed of communication.

•   Both the Platinum control and BMS must use the same Baud rate.

•   The communication is fixed to 8 Data Bits, No Parity, and 2 Stop Bits.

------ BAUD RATE -----

 9600

 19200

 38400

 alerT

MODBUS capable Platinum controls will display  

--NETWORK PANEL--

 

on the 2nd row of the display when in screen saver mode .

TrOUBleSHOOTIng

If no communication is the symptom, check the following:

•   Make sure that RS485 A(+) and B(-) terminals polarity is correct.  Otherwise, there will be no communication.

•   Both devices must have the same Baud rate.  Successful communication depends on matching the Baud rate of both devices.

•   Check that the RS485 G terminal is connected properly.

If intermittent communication is the symptom, check the following:

•   Make sure that the communication cable is of the twisted-pair type.

•   Reliable communication depends on the cable length and Baud rate used.  Long cable length may require a lower Baud rate.

Содержание MODBUS RTU RS485

















Отзывы: