heat-timer ETV Platinum Plus Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 56

background image

059305-00 Rev. D

Heat-Timer Corp.

Schedules Menu

The Schedules menu is used to configure schedules that are used to set an absolute temperature. Up to

four periods can be configured per day. Each period can have its own start time and temperature setting,

and will maintain that temperature setting until the next scheduled period start time.

NOTE:

Available only when Control Mode is set to ETV or ETV + TMC (see “Control Mode” on page

schedule is set, the schedule overrides the Setpoint setting (see “Setpoint” on page

).

Platinum Plus Display and Programming 47

«
...
45
46
47
48
49
...
»

Содержание ETV Platinum Plus

























































Отзывы:

Нет отзывов

Похожие инструкции для ETV Platinum Plus

Бренд: K&K Страницы: 6

Бренд: B&R Industries Страницы: 89

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Бренд: UCS Страницы: 4

Бренд: Icom Страницы: 30

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: ray Страницы: 11

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

Бренд: V2 Страницы: 12

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды