Heat-N-Glo Pier-38HV Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 30

Heat-N-Glo Pier-38HV Скачать руководство пользователя страница 18

22

B. Installing Vent Components
1. Attach the First Vent Component to the

Starting Collars

To attach the first vent component to the starting collars

of the fireplace:

Apply a 3/8 inch (9.5mm) bead of stove cement around

the 5 inch (127mm) fireplace starting collar.

Make sure that the fireplace rope gasket supplied with

the fireplace seals between the first 8-5/8 inch (219mm)

vent component and the outer fireplace wrap.

Lock the vent components into place by sliding the con-

centric pipe sections with four (4) equally spaced interi-

or beads into the fireplace collar or previously installed com-

ponent end with four (4) equally spaced indented sections.

When the internal beads of each 6-5/8 inch (168mm)

outer pipe line up, rotate the pipe section clockwise about

one-quarter (1/4) turn. The vent pipe is now locked together.

!

WARNING: A 3/8 INCH (9.5 MM) BEAD OF

STOVE CEMENT MUST BE PLACED AROUND

THE 4 INCH (102MM) FIREPLACE STARTING COL-

LAR BEFORE ATTACHING THE FIRST VENT COM-

PONENT. FAILURE TO SEAL THIS JOINT MAY

CAUSE THE FIREPLACE TO OPERATE IMPROPER-

LY. SEE FIGURE 16.

Figure 16. Attaching the First Vent Component

to the Starting Collars

STARTING

COLLAR

STOVE

SEALANT

BEAD

1 INCH

(25.4mm)

FIRST VENT

COMPONENT

WARNING: ENSURE THAT THE FIBERGLASS

ROPE GASKET SUPPLIED WITH THE

FIREPLACE SEALS BETWEEN THE FIRST VENT

COMPONENT AND THE OUTER FIREPLACE WRAP.

If the installation is for a termination cap attached directly

to the fireplace, skip to the sections,

Install Firestops

and

Vent Termination

.

2. Continue Adding Vent Components

To continue adding vent components in accordance with

the pre-planned vent system configuration:
Ensure that each succeeding vent component is securely

fitted and locked into the preceding component in the

vent system.

90° elbows may be installed and rotated to any point

around the preceding components vertical axis. If an

elbow does not end up in a locked position with the pre-

ceding component, attach with a minimum of two (2) sheet

metal screws. Continue adding vent components, locking

each succeeding component into place (see Figure 17).

!

Figure 17. Adding Venting Components

«
...
16
17
18
19
20
...
»

Содержание Pier-38HV































Отзывы:

Нет отзывов