manualshive.com logo in svg

Heat-N-Glo GRAND-50, Руководство по установке, Страница: 34 / 36

Поделиться
Скачать
Heat-N-Glo GRAND-50 Скачать руководство пользователя страница 34

31

Step 11

Before Lighting

the Fireplace

Before

 lighting the fireplace, be sure to do the following:

Review safety warnings and cautions

• Read the 

Safety and Warning Information

 section at

the beginning of this 

Installers Guide

.

Double-check  for  gas  leaks

• Before lighting the fireplace, double-check the unit for

possible gas leaks.

Double-check vent terminations and front grilles for

obstructions.

• Before lighting the fireplace, double-check the unit for

possible obstructions that could be blocking the vent

terminations or the front grilles.

Double-check for faulty components

• Any component that is found to be faulty 

MUST BE

replaced with an approved component. Tampering with

the fireplace components is 

DANGEROUS

 and voids all

warranties.

A small amount of air will be in the gas supply lines. When

first lighting the fireplace, it will take a few minutes for the

lines to purge themselves of this air. Once the purging is

complete, the fireplace will light and will operate normally.
Subsequent lightings of the fireplace will not require this

purging of air from the gas supply lines,

 unless

 

the gas

valve has been turned to the OFF position

, in which

case the air would have to be purged.

Step 12

Lighting the

Fireplace

You’ve reviewed all safety warnings, you’ve checked the

fireplace for gas leaks, you know the vent system is

unobstructed, and you’ve checked for faulty components.

Now you’re ready to light the fireplace.

WARNING

PLEASE REFER TO THE USER’S

MANUAL FOR ALL CAUTIONS, SAFETY,

AND WARNING INFORMATION

PERTAINING TO THE LIGHTING AND

OPERATION OF THE FIREPLACE.

The main and rear burners of this model are lit independently

by two 

ON/OFF

 rocker switches. The main burner 

MUST

be 

ON 

before the rear burner can be lit. The rear burner can

be either 

ON 

or 

OFF 

without affecting the main burner. See

unit wiring diagram - Figure 26.

After the

Installation

LEAVE THIS INSTALLATION  MANUAL

WITH THE APPLIANCE FOR FUTURE

REFERENCE.

Содержание GRAND-50





































Отзывы:

Нет отзывов