Heat-N-Glo GRAND-50 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 36

Heat-N-Glo GRAND-50 Скачать руководство пользователя страница 16

13

2. Continue Adding Vent Components

To continue adding vent components in accordance

with the pre-planned vent system configuration:

Ensure that each succeeding vent component is

securely fitted and locked into the preceding

component in the vent system.

Continue adding vent components, locking each

succeeding component into place.

Figure 11. Adding Venting Components

90° elbows may be installed and rotated to any point around

the preceding components vertical axis. If an elbow does not

end up in a locked position with the preceding component,

attach with a minimum of two (2) sheet metal screws.

WARNING: MODEL GRAND-50 REQUIRES

SHIELD SRV570-290 ABOVE THE FIRST 90°

ELBOW IN THE SYSTEM IF CLEARANCE

IS LESS THAN 4 INCHES (102MM). SEE

INSTALLATION SHEET AND HEAT

SHIELD SUPPLIED WITH FIREPLACE.

Figure 12. Placement of SRV570-290 Heat Shield

First 90 elbow in system.

3. Install Support Brackets
For Horizontal Runs -

The vent system must be

supported every five (5) feet of horizontal run by a

horizontal pipe support.

To install support brackets for horizontal runs:

Place the pipe supports around the vent pipe.

Nail the pipe supports to the framing members.

«
...
14
15
16
17
18
...
»

Содержание GRAND-50





































Отзывы:

Нет отзывов