Heat-N-Glo GRAND-50 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

Heat-N-Glo GRAND-50 Скачать руководство пользователя страница 15

12

B. Installing Vent Components

1. Attach the First Vent Component to the Starting Collars

To attach the first vent component (3 foot straight pipe

minimum) to the starting collars of the fireplace:
Apply a 3/8 inch (9.5 mm) bead of stove cement

around the inner pipe fireplace starting collar.

Make sure that the fireplace rope gasket supplied

with the fireplace seals between the first 8-5/8 inch

(219mm) vent component and the fireplace top.

Lock the vent components into place by sliding the

concentric pipe sections with four (4) equally

spaced interior beads into the fireplace collar or

previously installed component end with four (4)

equally spaced indented sections.

When the internal beads of each outer pipe line up,

rotate the pipe section clockwise about one-quarter

(1/4) turn. The vent pipe is now locked together.

1. Apply the stove

cement.

2. Line up the internal

beads and rotate the

pipe sections clock-

wise until locked.

3. Lock the vent compo-

nents into place.

4. Check the seal on the

rope gasket.

Figure 10. Attaching the First Vent Component to

the Starting Collars

WARNING: A 3/8 INCH (9.5 MM) BEAD

OF STOVE CEMENT MUST BE PLACED

AROUND THE INNER PIPE FIREPLACE

STARTING COLLAR BEFORE ATTACHING

THE FIRST VENT COMPONENT.

FAILURE TO SEAL THIS JOINT MAY

CAUSE THE FIREPLACE TO OPERATE

IMPROPERLY. SEE THE DIAGRAM .

WARNING: ENSURE THAT THE

FIBERGLASS ROPE GASKET SUPPLIED

WITH THE FIREPLACE SEALS BETWEEN

THE FIRST VENT COMPONENT AND

THE FIREPLACE TOP.

STARTING
COLLAR

STARTING
COLLAR

FIRST
VENT
COMPONENT

FIRST
VENT
COMPONENT

STOVE
SEALANT
BEAD
3/8" (9.5 mm)

STOVE
SEALANT
BEAD
3/8" (9.5 mm)

1 INCH (25.4 mm)

3/8 INCH (9.5 mm)

«
...
13
14
15
16
17
...
»

Содержание GRAND-50





































Отзывы:

Нет отзывов