manualshive.com logo in svg

Heat-N-Glo CFX-DIAMOND, Руководство по установке

Поделиться
Скачать
Heat-N-Glo CFX-DIAMOND Скачать руководство пользователя страница 3

3

Safety and Warning Information ........................ 2

Service Parts ...................................................... 4

Section 1: Approvals and Codes ....................... 6

Appliance Certification .......................................... 6

Installation Codes ................................................. 6

High Altitude Installations ....................................... 6

Section 2: Getting Started ................................. 7

Introducing the Heat-N-Glo Gas Fireplaces ........... 7

Pre-installation Preparation ................................... 7

Section 3: Installing the Fireplace ...................  9

Constructing the Chase ........................................ 9

Step 1 Locating the Fireplace ............................. 10

Step 2 Framing the Fireplace ............................. 11

Step 3 Installing the Vent System ....................... 12

A. Vent System Approvals ....................... 12

B. Installing Vent Components ................ 18

C. Vent Termination ................................. 23

Step 4 Positioning, Leveling, and

Securing the Fireplace ............................ 28

Step 5 The Gas Control Systems ...................... 28

Step 6 The Gas Supply Line .............................. 29

Step 7 Gas Pressure Requirements .................. 30

Step 8 Wiring the Fireplace ................................ 31

Step 9 Finishing ................................................. 32

Step 10 Installing Trim, Logs & Ember Material ... 34

 Installing the Trim ................................... 34

 Shutter Settings ..................................... 34

 Positioning the Logs .............................. 35

 Placing the Ember Material .................... 35

Step 11  Before Lighting the Fireplace ................. 37

Step 12 Lighting the Fireplace ............................. 37

After the Installation ............................................. 37

Section 4: Maintaining and Servicing

      Your Fireplace ...............................  38

Table of
Contents

‹

 =  Contains updated information.

‹

‹

Содержание CFX-DIAMOND






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды