Heat-N-Glo CFX-DIAMOND Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 37

Heat-N-Glo CFX-DIAMOND Скачать руководство пользователя страница 10

12

Vent system components

Vent system

termination kits

Figure 4. Vent Components and Terminations

Step 3
Installing the
Vent System

A. Vent System Approvals

This model is approved to use D-Series components
and terminations. Approved vent system components
are labeled for identification.

NO OTHER VENTING

SYSTEM OR COMPONENTS MAY BE USED

.

Detailed installation instructions are included with each
vent termination kit and should be used in conjunction
with this

Installers Guide.

The drawing below shows

vent system components and terminations.

The flame and ember appearance may vary based on
the type of fuel burned and the venting configuration used.

Identifying Vent Components

The vent systems installed on this gas fireplace may
include one, two, or three 90

o

elbow assemblies. The

relationships of vertical rise to horizontal run in vent
configurations using 90

o

elbows

MUST BE

strictly

adhered to. The rise to run relationship are shown in the
venting drawings and tables. Refer to the diagrams on
the next several pages.

NOTE: TWO 45

O

ELBOWS MAY BE USED IN PLACE

OF ONE 90

O

ELBOW. RISE TO RUN RATIOS IN

THE VENT SYSTEM MUST BE FOLLOWED IF 45

O

ELBOWS ARE USED.

DVK-TVCD

DVK-01TRD

DVK-01D

VERTICAL
TERMINATION

HORIZONTAL
TERMINATION

WALL FIRESTOP

90 DEGREE ELBOW

CEILING FIRESTOP

WALL BRACKET

PIPE LENGTH

HORIZONTAL PIPE SUPPORT

ROOF FLASHING

STORM COLLAR

HEAT SHIELD

«
...
8
9
10
11
12
...
»

Содержание CFX-DIAMOND






































Отзывы:

Нет отзывов