manualshive.com logo in svg

Heat-N-Glo CFX-DIAMOND, Руководство по установке

Поделиться
Скачать
Heat-N-Glo CFX-DIAMOND Скачать руководство пользователя страница 28

30

• The gap between the

supply piping and gas
access hole can be
plugged with non-
combustible insulation
to prevent cold air
infiltration.

• Insert insulation from

the outside of the
fireplace and pack the
insulation tightly to
totally seal between the
pipe and the outer
casing.

• The gas line

should be
installed by a
qualified service
technician.

Figure 25. Gas Supply Line

Step 7
Gas Pressure
Requirements

Pressure requirements for these gas fireplaces are
shown in the table below.

Pressure

Natural Gas

Propane

Minimum

7.0 inches

12.0 inches

Inlet Pressure

w.c.

w.c.

Maximum Inlet

14.0 inches

14.0 inches

Gas Pressure

w.c.

w.c.

Manifold

3.5 inches

10.0 inches

Pressure

w.c.

w.c.

A one-eighth (1/8) inch (3 mm) N.P.T. plugged
tapping is provided on the inlet and outlet side of the
gas control for a test gauge connection to measure
the manifold pressure.

The fireplace and its individual shut-off valve must
be disconnected from the gas supply piping system
during any pressure testing of the system at test
pressures in excess of one-half (1/2) psig (3.5 kPa).

The fireplace must be isolated from the gas supply
piping system by closing its individual shut-off valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than one-
half (1/2) psig (3.5 kPa).

GAS CONTROLS

USE A WRENCH

ON SHUT-OFF VALVE

WHEN TIGHTENING

GAS LINE.

MANUAL

SHUT-OFF

VALVE

GAS VALVE

FLEX

CONNECTOR

Содержание CFX-DIAMOND






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды