Heat Link PEX-a Скачать руководство пользователя

Страница: 36 / 44

Link

Heat

Issue

Resolution

Stainless Steel Press Sleeves

Tubing not seated all the way

onto fitting

Cut out fitting, and replace with new sleeves and fitting.

Does not pass Go/No-Go

Cut out fitting, and replace with new sleeves and fitting.

Tubing not cut straight

Cut out fitting, and replace with new sleeves and fitting.

Press sleeve not pressed

properly

Cut out fitting, and replace with new sleeves and fitting.

Press Failure

Cut out fitting, and replace with new sleeves and fitting.

Pinched Sleeve

The tool is out of calibration or the tool jaws are worn out or

damaged and must be replaced.

Fittings

Cracked

Cut out fitting, and replace with new sleeves and fitting.

Fitting Barbs are Damaged

Cut out fitting, and replace with new sleeves and fitting.

PEX Tubing

Notched or Cut

Cut out section of tubing and use appropriately sized coupling.

Repairs in concrete must be wrapped. HPP fittings are recommended

for concrete repairs.

Kinked

Kinked tubing can be repaired using a heat gun.

See

page 9

for details.

Frozen

Can be thawed using hot water, hot towels, or gently heating with a

heat gun.

Do Not Use Open Flame!

Tools and Jaws

Cracked Jaws

Power press tools are pressed with empty jaws. Replace the jaws.

Chipped Jaws

Tools being used for unintended applications. Replace the tool/jaws.

Common Installation Issues

Содержание PEX-a













































Результаты поиска

Содержание PEX-a

Отзывы:

Похожие инструкции для PEX-a

Бренды по названию

Популярные бренды

Heat Link PEX-a, Руководство по установке

Результаты поиска

Содержание PEX-a

Отзывы:

Похожие инструкции для PEX-a

Бренды по названию

Популярные бренды