Heat Controller VMH 30 Series Скачать руководство пользователя страница 8

7

Heat Controller, Inc. 

VMH 30/36 SERIES

 

Installation, Operation & Maintenance

Install the outdoor unit on a rigid base to prevent increased noise levels and vibration.

Ensure the air outlet is not blocked by any objects such as plants or walls, etc.

If the installation location is exposed to strong winds, ensure the unit is placed lengthwise along 

the wall or provide a switchable baffle to block strong wind gusts from entering the unit.

If suspending the unit with a bracket, follow the bracket manufacturer’s installation instructions.

Use a raised concrete pad or concrete blocks to provide a solid base and level surface - securely

anchor the unit down with bolts. See table & figure below.

In a snowy area, install the outdoor unit on a raised platform higher than drifting snow.

Seal

Drain elbow connector

Base pan hole

of outdoor unit

(A)

(B)

              The pictures of the drain joint may very from the actual 

part that come with the unit.

Push the seal onto the end of the drain elbow connector (Fig. A), 

then insert the drain elbow connector into the hole in the bottom 

of the base pan of the unit (Fig. B) until it makes a click sound 

and is firmly in place. Add an additional drain hose to direct the 

condensate away from the base of the unit by placing a hose  

on the end of the hose barb. This drain hose is not included with  

the unit and must be purchased.

2

DRAIN JOINT INSTALLATION

OUTDOOR INSALLATION PRECAUTION

1

NOTE: 

Anchor the outdoor unit with a bolt and nut  

( 10mm) or 

 tightly and horizontally 

on a concrete or rigid mount.

Ø3/8” Ø

Ø5/16”(Ø8mm)

Outdoor  unit  dimension

          in(mm)(L1xHxW1)

L2(mm)

20.6in.(523)

W2(mm)

13.4in.(340)

20.9in.(530)
23.6in.(600)

11.4in.(290)
12.6in.(320)

22.1in.(560)
23.2in.(590)

18.9in.(481)

13.2in.(335)
13.1in.(333)

10.9in.(276)

Mounting  dimensions

32.3x23.4x13.0

29.9x23.2x11.2

30.5x21.4x12.2

33.3x27.6x12.6
35.4x33.9x12.4

26.4x21.3x9.8

Settlement of outdoor unit

(820x595x330)

(760x590x285)

(775x545x310)

(845x700x320)
(900x860x315)

(670x540x250)

OUTDOOR SECTION

Содержание VMH 30 Series













Отзывы: