Heat & Glo VRT-BK-N-AUB Скачать руководство пользователя страница 2

Страница: 2 / 76

Heat & Glo • VRT-AUB • 2123-980_R14 • 12/14

PLEASE READ THIS MANUAL BEFORE INSTALLING

AND USING THIS APPLIANCE.

IMPORTANT:

Read all instructions carefully before starting installation.

Failure to follow these installation instructions may result in a possible fire

hazard and will void the warranty. Save this manual for future reference.

It is the responsibility of the professionals involved with the service and installation of the appliance to test the

operation of the appliance before leaving the installation site.

Heat & Glo, a brand of Hearth & Home Technologies

352 Mountain House Road, Halifax, PA 17032

MODELS: VRT-N-AUB AND VRT-P-AUB ARE SAI GLOBAL

APPROVED FOR NATURAL GAS, PROPANE OR BUTANE

AS A BALANCED FLUE FIREPLACE.

Refer to the appliance data plates for gas consumptions and

pressures.

Installation of this appliance should only be carried out by

an authorized person in accordance with the manufacturer’s

instructions. Appliance is to be installed in full compliance

with the manufacturer’s instructions, and any local authorities’

requirements for gas, electrical and building regulations.

This appliance and its components are tested and safe

when installed in accordance with this Installation Manual.

Report to your dealer any parts damaged in shipment,

specifically check glass condition. The gas logs and flue

system components are in separate packages. Read all

instructions before starting installation and follow these

instructions carefully during installation to ensure maximum

benefit and safety.

Failure to follow them will void your warranty and may present

a fire hazard.
The Heat & Glo, a brand of Hearth & Home Technologies

warranty will be voided by, and Heat & Glo, a brand of Hearth

& Home Technologies disclaims any responsibility for the

following actions:

• Installation of any damaged fireplace or flue system

component

• Modification of the fireplace or balanced flue system

installation other than as instructed by Heat & Glo, a

brand of Hearth & Home Technologies.

• Improper positioning of the gas logs or the glass door
• Installation and/or use of any component part not

manufactured or approved by Heat & Glo, brand of Hearth

& Home Technologies, not withstanding any independent

testing laboratory or other party approval of such

component part or accessory.

Содержание VRT-BK-N-AUB













































































Результаты поиска

Содержание VRT-BK-N-AUB

Отзывы:

Бренды по названию

Популярные бренды

Heat & Glo VRT-BK-N-AUB, Руководство пользователя

Результаты поиска

Содержание VRT-BK-N-AUB

Отзывы:

Бренды по названию

Популярные бренды